ender 3 v2 auto leveling 3d models
901618 3d models found related to ender 3 v2 auto leveling.
thingiverse
This is a remix of LaurentRueil's "5” Slim HDMI monitor case for Raspberry and other" designed to mount on an Ender 3 using 3 T-Nuts like in the original Ender 3 V2 screen mount design. ... - 4 X 2mm Screws are needed for the case
prusaprinters
Here's the fan duct for the Ender-3 or the Ender-3 V2. https://www.simscale.com/projects/SeanChang/ender-3_v2_4010-4020_fan_duct/ Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament:...
thingiverse
Designed this based on other "Prusa-like" knobs that I saw here, but I decided to make it a little bit smaller and a snug fit for the Ender 3 v2. ...
thingiverse
this is a front facing switch box I designed for the V2 to move the switch to the front. ... I would print with supports for the box Check out my other things for Ender 3 Pro Switch Box
thingiverse
A simple cover for the LCD on the ender 3 v2. Comes in a few variations, with or without a window for the temp readings. ... UPDATE: Added models with bigger windows for the newer Marlin UI update
thingiverse
A Led ring for the new Creality Ender 3 v2. Great especially when used with cameras and Octopi! You will need approximately 20cm of Led strip. ...The led strip should be attached internally.
thingiverse
Bed mounts for an ender 3 v2 designed these after being recommended Silicone bed mounts, after 2 weeks of use I have had no issues nor have I had to re tram the bed. ...
cults3d
Hotend cable holder for Ender 3 V2, attaches to the screws (replace with longer ones) that hold the power board. ... If you see any improvements, don't hesitate to ask.
cults3d
A simple cover for the LCD on the ender 3 v2. Comes in a few variations, with or without a window for the temp readings. ... UPDATE: Added models with bigger windows for the newer Marlin UI update
thingiverse
This is case for a two way to mount on the side V-Slot of an Ender 3 V2. I use this relay for switch the light from octoprint. ...
thingiverse
made for use with bearing ZNL 1000806 2RS 61806 6806 and ESUN filament coil fix some problems with filament stuck replace default filament holder from ender 3 v2 neo, use default nut
prusaprinters
A simple model of a mount for the screwdriver that comes with the Ender 3 V2.I'd reccomend a layer height no more than 0.16mm.
thingiverse
A solid version of https://www.thingiverse.com/thing:5110844/remixes Could be used as is and glued to something or added to 3D model. ... Was originally for the Ender 3 V2 drawer knob
thingiverse
Slightly modified version of original Ender 3 V2 Tool Holder. Modified rails for a snug fit and adjusted shorter one to hide nicely behind snap covers. ... Also spatula tool and USB drive fit nicely now.
thingiverse
This is an adapter to fit the stock ender 3 v2 fan on https://www.thingiverse.com/thing:4636003. ... I tried to make it a remix but it does not seem to be working
thingiverse
Remix of sweet guide by Markacho to work with BMG extruders and clones Should work for ender 3, pro, and v2 Everything snaps in place, just print one of each Uses a 608 bearing
thingiverse
This adapter fits to creality ender 3 v2 stock spool holder to easily rotate filament spools with 56mm or 54mm mounting diameter. ...Two STL files include with 56mm and 54mm adapters.
thingiverse
Creality Ender 3 V2 Neo. ... Assembly hardware: 4X - Stock M3 filament sensor screws 4X - M3 nuts 1X - Stock Nyloc nut from top X motor/wheel mount bracket Top and bottom layers .8 Walls .8
thingiverse
This is a remix of https://www.thingiverse.com/thing:4665097 for the Creality Ender 3 v2 Neo because the rubber pads on the Neo were slightly too big to fit into the original design.
thingiverse
Redesign of some cableclips for the Ender 3 V2 that replaces zip ties to keep cables together with PTFE tube running to the extruder. ... These clips open at the bottom and won't brake that fast.
thingiverse
This is just a remix of the Ender 3 V2 Riser Feet 25 & 35 mm project to allow for additional space below for a 120mm fan for my motherboard and PSU. ...All about airflow!!!
thingiverse
Moved 1 hole to fit the Creality Ender 3 V2 backplate. Tested and fitted. This is a remix of the Hydra from BoothyBoothy. ... https://www.thingiverse.com/thing:4062242
thingiverse
A simple snap on cover to go onto your ender 3 V2 to change up the color scheme. Download either the desktop inventions logo or the blank cover and add you own logo. ... https://youtu.be/cQxz2GkAC9c
thingiverse
I close my ender 3 v2 on a IKEA lack table and i need to mount my screen outside so i make a remix of this mount to support my display on angle to see better the screen
prusaprinters
Blank QR code cover for Ender 3 V2.I left it blank so you can merge any Logo of your choice.Fits perfectly!
prusaprinters
I repositioned the PSU on my ender 3 v2 for better cooling so I made this safety cover to cover the dangerous bits. ...The small opening in the cover is for the cables to pass through.
cults3d
Basic QR code cover for the Ender 3 V2 with a spider. ...Simple easy quick print If you have a CR or BL Touch you "may" need to trim the side facing the hot end depending on your clearance.
thingiverse
Display Cover for Ender 3 V2 After printing found flaws did not fix in stl knob https://www.thingiverse.com/thing:4772611 https://www.youtube.com/watch?v=4TuCHvzSheI
thingiverse
This is a two piece mount to hold a 12" LED cabinet light to the factory included filament holder on the Ender 3 v2. Used two - M6x1.0x50mm nuts and bolts to secure it the mount to the printer. ...
cults3d
Yoda bust cover for the QR code on Ender 3 v2 Combined in Tinkercad. ...Original authors of the models used should get all the credit :) With you, may the Force be ...