ender 3 v2 camera mount 3d models

Print with supports touching build plate0.2 layer height3 walls

https://www.thingiverse.com/thing:4177240 remix IP camera stand for ender 3 series and 40x40 sigma profile

Remixed to allow a different orientation for the spool holder on my printer. ... This angled version mounts on the right or left side and holds the spool above the printer bed without colliding.

This mount screws into the end of the gantry, it holds a microswitch to trigger a phone to take a photo. ... For full details see my video here: https://fsc.co.nz/3dtimelapse/

Added pen mount for drawing on stuff. Pretty simple and oh so effective. ... Merge of : https://www.thingiverse.com/thing:4560739 and https://www.thingiverse.com/thing:3139205 Print the housing from SAWoosh.

This is my creation of a Y axis fan mount. I recently did a 24hr print and I noticed the y axis motor was kinda warm. ...It is designed to accept a 4010 size fan, preferably a 2 wire 24V.

This mount was designed to include the top bracket for extra support as well as serve as a place to install the ADXL345 circuit board for input shaper using Klipper.

... a 1 meter or longer 10 pin connector it is designed to fit around a top z axis brace. this model just sits on the 2020 rail. it is to be printed on its side to minimize supports needed the only supports are in the mounting holes for the screen

......For the Ender boards or SKR. Not sure what else will fit. Moved the left side fan hole over and mirrored it over to the right so the pi and main board both are getting a good solid flow of air across the hot bits. Also added the honeycomb cutouts.

... from (https://www.thingiverse.com/thing:4785189) but made it possible to connect the links for the X axis cable. *Total package will be updated soon, for better alignment en fitting the directdrive mount I remixed, see my other designs. ...

The heat block is mounted with the heater element facing backward so it's easier to see the nozzle. Printed it in PLA+,and have been printing PETG for 80 hours @ 240°C and nothing has melted. I put a piece of Kapton tape to shield some heat from...

Found that the print was hitting one of the other screws on the mounting plate. Cut out a piece from the original STL so it would fit without filing down the side. Mounts with two M3-.05 x 8mm. The 8mm sticks out a bit from the plate but does not...

If somebody has hard time trying to mount this case to his/her printer, like I had, than maybe want to try my remix. For me it worked like a charm from the first try, both in PETG or PLA. ... I used supports, but it's not a request...not at all.

See the images for the exact model of webcam usedunscrew the webcam from the base and screw it to the webcam mount using the included nutremixed from https://www.thingiverse.com/thing:5154496

... - 2x m3 bolt(1cm) and nuts. - 2 bowden tube connectors. - 10-15 cm bowden tube. - 2x m4 bolt and nuts for mounting the arm. (You can see the detailed drawings of the mount in the original design) Buy me a beer PayPal.Me/cagataykilinc

... 2x m3 bolt(1cm) and nuts. 2 bowden tube connectors. 10-15 cm bowden tube. 2x m4 bolt and nuts for mounting the arm. (You can see the detailed drawings of the mount in the original design) Buy me a beer PayPal.Me/cagataykilinc

https://www.amazon.com/gp/product/B06Y3NWN8R/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 That is the led light I purchased to mount using 2 of these brackets. 20% infill No Supports I used PLA. If you enjoy my designs you could always buy me...

... better. ...It also utilized a different body that was slimmer. UPDATE 3/6/22 - Added a version with a 10mm lift for better viewing angle upon request. UPDATE 3/7/22 - Added a version with a 50mm lift for better viewing angle upon request. ...

I have the dual gear metal extruder upgrade, I sized the height of the mount to this extruder so it goes in straight. maybe other extruders will have a slight height difference. There are two rollers. That way if you mount your material up top it...

November 2020 update: I've added a v3 model which has an alternative mount on the rail. This may fix any problems you have with the reel leaning out to the side, as the new one is has vertical contact with the side of the rail. The support may be...

... bolt(1cm) and nuts. 2 bowden tube connectors. 10-15 cm bowden tube. 2x m4 bolt and nuts for mounting the arm. (You can see the detailed drawings of the mount in the original design) Buy me a beer PayPal.Me/cagataykilinc Category: 3D Printer Parts

Minor mods to the excellent must-have Dial Gauge Holder by Mike Guyre: - Added more end-stops to seat the holder more squarely - Moved the gauge mounting hole back a little so the rear of the gauge sits flat against the mounts (see caveats below) -...

Hello, This mounts directly to the top left side of your stock extruder plate using the roller bolt to hold it on. It does not interfere with your X axis limit switch. It is not heavy. I printed this from PLA 200C 60C with 20% fill You will need...

... tight. Keep infill 80+ to ensure full strength. Do note that it requires wire of extruder motor to be extended so be prepared before mounting. ...Extending cable does not necessary, you can cut wire, join extra cable in between and solder those.

This is a remix of this mount by Whitefiretiger : https://www.thingiverse.com/thing:5559571 This is designed to work with this specific Arducam Enclosure: https://www.thingiverse.com/thing:5350571This is also designed to work with this specific...

3 inserts M3 needed for mounting on the printer Use with a dia.8 camera

Mounts for Pi and Pi camera are attached to Ender 3 using M5 cap screws and T-Nuts securely. A single arm is sufficient for the camera, but both long and short arms have been posted for options. Personally, I've chosen to use the longer arm and...

The Holder can be mounted on to the rail at the site of the Ender 3 V2 without Screws. The Pi with Case can be slided in the Holder. A Holder for the Pi Cam can be attached at the top of the Pi Case Holder. ... I use a Case from:...

... ...This design is specifically tailored for use with ModMike's "Creality Ender 3 Pi Cam Mount", a popular 3D printed accessory available on Thingiverse at https://www.thingiverse.com/thing:2886101.

I also used some M3 screws with T-Nuts to secure the arm to the Printers 2040 Extrusion.This was printed in PLA+ with supports for the holes on the mount base, no supports for the arm, just print it...