ender 3 v2 camera mount 3d models

I printed the original camera mount after setting up Octoprint for my Ender 3 Pro. It was perfectly fine, but it started to move by quite a bit every time the printer homed. I redesigned the arm connecting the mount to the camera holder to minimize...

While I was at it, I made the other hole in the camera mount arm and the place it attaches the same 0.25 inch size. This remix contains only the modified parts. Get the other parts from the original. (Thingiverse requires at least one file of a...

The Wyze V2 Camera Mount is a top-notch accessory that seamlessly integrates with the Ender 3 Level Bed, delivering outstanding performance and reliability. With its sturdy design and precise engineering, this mount provides a rock-solid foundation...

This allows you to mount a Raspberry Pi V1/2 camera with a Neopixel LED strip to your Creality Ender 3 v2 Neo printer. Parts required: - Raspberry pi camera (I used [this one](https://www.amazon.co.uk/gp/product/B098F1BWF2/) with a 50cm ribbon ) -...

Need 4xM3 45mm screws for this work, overwise you will not be able to screw into the stepper motor.

I created a mounting bracket for a Xiaomi YI 1080p surveillance camera adaptable on an Ender 3 pro or for another printer 100% screw filling Support according to the models spring for bottom x-axis

i extended the arm for about + 50mm to go out of the way when you use a HeroGen5 Head and BLTouch

I modified this design to work with the BL Touch 2mm Extension Satsana Duct designed for the Micro Swiss Full Metal Hot end. ... For use with this fan shroud specifically https://www.thingiverse.com/thing:4689712

Habe leider keine passende Halterung gefunden, welche sich ohne Schrauben etc. befestigen lässt, daher der Entwurf. ... Hält wirklich sehr fest, wenn das Bauteil seitlich zwischen den Rillen richtig angedrückt wird (siehe Bilder) Halterung hat...

Ender 3 V2 camera mount fixed to bed. ... Note that this is due for rework as fixing the mount ABOVE the bed springs puts them in contact with the hot bed that allows the PLA to soften and warp.

Replaced an old usb webcam casing with this one and created the holder to attach to the ender 3 v2. ...The black parts are made of PLA and orange ones TPU

Slides on the front of the Ender 3 Y-axis and is compatible with cameras that use the 1/4 inch tripod mount. ...Make sure to check for clearance of the bed and camera.

Ender 3 camera mount, designed for the TP-Link Tapo C100 Security Camera. However it will work with other cameras with a little tweaking which is why I have uploaded the sketchup file also. This replaces the X motor cap. ...I would recommend going...

Simple mount for a camera on the Ender 3. It fits over one of the V roller nuts on the right side of the X axis and is secured with an additional M5 nut. I designed it for the internals of an old webcam that I had, but it should also fit a Raspberry...

The plan is to install a standard USB camera on top of the construction plate by attaching it to the Ender 3's Y-axis clamp.

This is a modified version of RaffoSan's Ender 3 bed camera mount, now equipped with the GoPro-style connector from yyh1002's Modular Mounting System. The combination makes for an excellent time-lapse rig. To achieve optimal strength, print this...

This is a remix of RaffoSan's Ender 3 bed camera mount https://www.thingiverse.com/thing:2999957 . It has the gopro style connenctor from yyh1002's Modular mounting system. ...Together this makes a great time lapse rig....

This is a custom webcam mount designed specifically for the C270 Logitech Webcam on the Ender 3 3D printer. It attaches directly to the Y-Axis Tensioner. Due to its structural importance, this mount should be printed with high infill density and 4-6...

I designed this in Tinkercad to specifically mount the Ring camera, but could be used to sit any camera of like size on top of the platform. It uses the frame screws next to where the SD card slot is to mount to the printer and M3 screws and nuts for...

This is a mount for a generic PTZ camera, or any camera with a standard 1/4" tripod screw mount. It bolts on to the front left leg of the printer using the existing screws. ...There's a hole punched through the piece to allow easy tightening of one of...

Designed for an Ender 3 Will probably work on other printers too. ...Works with a Blink camerahttps://www.amazon.de/gp/product/B07X37DT9M/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Three components creating an azimuth-elevation mount for the camera. Connected via two short M3 screws (I used 5mm and 6mm). ...Nuts required.</p><p>&nbsp;</p><p>The view of the print is slightly obstructed by the print head but it gives a nice overview...

This is a bed mounted camera mount for a sony lifecam webcam. I installed this after I had a mount attached to the x-axis so that I can get better time lapses with octoprint. I also added points for zip-ties to hold the webcam cable. Also designed...

I use this for my bed camera.

The swivel on the camera needs to be taken apart, and the weights must be detached after that it fits snugly in place. Print in ABS at 250 degrees Celsius with a 20-40% infill rate and a bed temperature of 108 degrees Celsius. ... The camera bolts...

I wanted an extruder mount that used the screws to attach for a stronger and more rigid part. ...I saw one like that in a YouTube video, but I could never find the model, so I made my own.It needs a new x-endstop switch piece so that you can use the...

I made this clamp to hold down a Microsoft LifeCam VX-5500 to my Ender 3 v2. It's not pretty but it does the job. One M3 hex screw and nut is required which came from this kit below. https://www.banggood.com/custlink/3DvRSMzhP6. The knob used...

ESP32 Camera Enclosure and Mount for Ender 3 v2

Ender 3 s1 Camera Mount

Creality Ender 3 Pro/V2 Quick Release Yi Home Camera Mount Note: Angled Arm version tilts the camera down 7*.