ender 3 v2 dimensions 3d models

This is a cover for the mother board of Creality Ender 3 v2 which allows installing a 40x20 cooling fan. ... Inspired by this design: https://www.thingiverse.com/thing:4683915

Remix of: https://www.thingiverse.com/thing:2479455 Toggle switch housing for mounting on the side of your Ender 3 v2. Sits flush with aluminum frame. ... I used 2 8mm M4 screws and t-nuts for mounting

Remix of a nice compact Ender 3 V2 handle that attaches to aftermarket 8mm bed spring. My bed screws were too short for the original design once I installed the new yellow bed springs. ...

For Ender 3 V2 A cover to put on the Power supply fan, which is very noisy during printing. ... Allow to reduce the noise during printing Just glue it using hot glue in front of the fan hole

This is a replacement knob for the belt tensioner on the Ender 3 v2. ... It's made from 2 parts that are meant to be glued together after inserting an M4 nut.

Improved BLouch mount for Creality Ender 3 v2. Added special mount holes for M3 nuts. Added small cut in the right upper corner to avoid connection with screw. Enforced plate to avoid deformation by temperature. ... ABS is recommended for print.

I searches for a working direct drive dual gear adapter, found some, nothing worked for my ender 3 v2, so i remixed one, hope it helps some others ^^ Update_v3 - Little more Stability

This is remix to be compatible with Ender 3 V2 extruder plate which is has different screw hole. I also add BLTouch mount to straight blower holder. ... BLtouch offset 34.5, 9

Remixed LED lighting for my Ender 3 V2 Neo printer. You can use your ring youtuber led lighting by adding a camera screw. ... Original Sources; https://www.thingiverse.com/thing:2749041 https://www.thingiverse.com/thing:2973859

This is remix of this thing https://www.thingiverse.com/thing:4623647 I just cut out a part for direct drive holder. ... Ender 3 V2 direct drive holder by JamieBK https://www.thingiverse.com/thing:4555065

This is support for the Ender 3 v2 Screen. There are 2 versions. ... - using stock screws - without screws Here is the video about : https://youtu.be/JEx4cRLCbPQ Can be printed support less on the top face.

This adapter will fit for the Ender 3 Pro V2 Compact SD Card Adapter Housing V4 https://www.thingiverse.com/thing:4609997 I`ve designed this to fit a microsd extension in the sd slot. ...

Foot extender for 3D printer Creality Ender 3 v2. ...The design is similar to one https://www.thingiverse.com/thing:4603075 , but with internal loaded walls, instead of infill.

couldnt find this so i created it. ...this is the x axis cover for the belt tensioner on the Ender 3 V2 NEO (only!)Printed at0.16mmPLAScrew mount side up on plater

All the parts needed for ender 3 v2 cable managment with chain links, i remixed multiple models i found online to make what for me was an optimal setup with the least amount of tikering of the printer parts

My attempt at another Ender 3 V2 accessory. This sits on your horizontal top rail and your lead screw. Additionally, the extra arm works as a filament guide. ... Enjoy!

Installed with zip ties. ...Converts 75mm & 55mm spools to 37mm. For use with Ender 3 V2. Simple solution to reduce drag and unspool smoothly. Stops spool from rocking. ...Comment for changes.

Meant for the ender 3 v2 y axis pulley. ...If your y axis belt is not perfectly centered on the pulley and/or rubbing your frame these simple rings will fix it.

... plug. This model press fits onto the stock Creality Ender 3 v2 controle knob with no modification needed! I recommend printing the Post and Plug in high detail. ...This works with the Creality Ender 3 v2; I have not tried it on any other printers.

... it. ...Also the other remixes with the "crosses" did not hold the thing in place. So I designed I screw using OpenSCAD based on this design https://www.thingiverse.com/thing:193647 that exactly fits the holes of the 4040 frame of the Ender 3 V2.

... ... Adapted to the Ender 3 V2 printer with Phaetus dragonfly BMS hotend and possibility of installing a BLtouch, Offset [-45, -10, 0] --------------------------------------------------------------- Voici un petit remix de du fan duct Red Squirrel.

I made this to attach a 1" travel dial indicator to my Ender 3 V2. It requires a CRTouch bracket (though not necessarily the sensor itself). It mounts above the bracket using the brackets mounting bolts. The indicator I am using is this one...

I modified the original frame: https://www.thingiverse.com/thing:4699164 I flipped it to fit the right side of ender 3 and replace the ender 3 original screen. ... I changed it a bit to fit the BigTreeTech Pi TFT50 v2.1

Original did not line up with the feeder very well on my Ender 3 V2. Should fit the Ender 3 as well, but not tested. Created in TinkerCad so pretty basic design. Slides in place tightly on top of stepper motor. ...No additional tools or screws...

Example listings: https://www.aliexpress.com/item/1005002628710810.html https://www.amazon.ca/PTCinder-Creality-Upgrade-ADAPTERS-Competent/dp/B0B5SZVQ5M/ Endstop-Body-2040.stl is for 2040 extrusions (Ender 3), Endstop-Body-4040.stl is for 4040...

Ender 3 V2 Y-axis dual linear rail I'm using 2x MGN9 linear rail (length 300 mm) 2x MGN9H carriage block stock Ender 3 bed Parts to be printed: 2x mount_single.stl 6x support_plate_rail.stl 1x stop_extension.stl

Using 2 existing bolts on the left extrusion of Ender 3 V2/S1/Neo Guide: print everything from the original design & lower arm here. Keep together using m3x30 screw. ... I got the mount base from here...

This is a direct drive Orbiter V2.0 extruder paired with a collar mounted E3DV6 Revo hot end and linear rail upgrade for the Ender 3. It was remixed from this posting on Printables...

Hobbled together something that will work to properly allow the NG extruder to hit the X-Axis limit switch on the Ender 3 V2 Neo from Creality. ...The switch style is that of the Ender 3 S-1 model which lays flat instead of vertical.

I modified my son's filament sensor mount to be able to mount the Creality filiment sensor on my Ender 3 V2. https://www.thingiverse.com/thing:4890156 His mount corrects alignment issues of other mounts for the Ender 3. ...His uses the repurposed Z...