ender 3 v2 direct drive with bltouch by5 3d models

Support to mount a BMG clone extruder in an Ender 3 V2 using the stock hotend. ...This support uses the fan case screw to improve rigidity.

Useful links regarding the BLTouch: BLTouch Documentation: https://www.antclabs.com/bltouch-v3 Marlin Firmware (now configurable for Ender 3 V2): https://marlinfw.org/ Already configured firmware: https://marlin.crc.id.au/ Creality Firmware:...

For the cable chains : From base to old extruder motor position : *1x chain-link_cut + 21x chain-link + 1x chain-link_cut* From base to plate : *15x chain-link + 1x [Y_axis_chain_connector](https://www.thingiverse.com/thing:4316238/files)* From old...

LK Drive is a direct drive setup designed specifically for Ender 3 or other compatible printers. The system incorporates the E3D V6 hotend and BMG Extruder as its core components. ...My primary objectives were to: - Enhance printing reliability -...

Made a rough version that doesn't interfere with Z axis nut for direct drive converted setups. ... Currently using it with this: https://www.thingiverse.com/thing:4789619 Slim links can still be acquired from remix source:...

... the mount in place of the larger idler wheel mount screw. I believe they are m2.5x0.45 screws. I used the wiring guide and configuration/firmware found here: https://smith3d.com/ender-3-v2-bltouch-firmware-installation-guide-by-smith3d-com/

Satsana for Creality Ender 3 V2 remix adding a BLTouch mount. This design works with stock fans. Added a 5015 version remix of Scrath_ https://www.thingiverse.com/thing:4647053 (Sorry but I can't add this one to remix source files because...

This is a new design to enable Direct Drive on Ender 3 V2 with out modifying any original parts. Take note that this only works for Metal Extruder single drive design and not yet tested on original Extruder and other types. I will be making one for...

The mount is actually for ENDER 3 SILENT FANG NOCTUA V2 (https://www.thingiverse.com/thing:4223929) This mount has the same characteristics of the original mount except this one has a BLTouch bracket. I found neither the factory bracket or the...

I bought one of those "cheap" "3DTouch" devices which claimed to suit the Ender 3 V2. The correct mount (and the cable supplied) doesn't fit the V2. You can cut and drill the supplied mount and it will fit but my supplied 3DTouch is a bit longer...

...We'll see how it holds up, but so far so good... There are apparently 2 versions of the Ender 3 V2 - One of the versions does not have the mounting holes that this attaches to, so... ...:/ The nozzle to probe offset I'm using with this is X-40, Y-7

If you have a Creality Ender 3 V2 with the BLTouch bed leveling sensor mounted using the L-bracket with bent finger, this is an alternative endstop for A-make-design's X-axis damper spacer (https://www.thingiverse.com/thing:3367587) All you will need...

Simple BL Touch mount for Ender 3 V2, using 2 pcs M3 Screw STL parts are pre-oriented for easy print and good results Additional parts needed : M3x6 Button Head/ Hex Screw 4 Pcs M3 Nut 2 Pcs Probe offset for the firmware: X-42,Y-5 Original Creality...

Simple BL Touch mount for Ender 3 V2, using 2 pcs M3 Screw STL parts are pre-orientated for easy print and good results Additional parts needed : M3x6 Button Head/ Hex Screw 4 Pcs M3 Nut 2 Pcs Probe offset for the firmware: X-42,Y-5 Original Creality...

I used Parametric Parts' thread creator to make the screw threads in the model (just to make it easy to add the threads): http://store.parametricparts.com/store/p3/Thread_Creator_for_Onshape_(BETA).html Do note that you need the mounting holes for...

I changed the direction and size of the blowing nozzle so that the air stream falls under the nozzle, the size of the hole for the fastening nut (previously the nut did not fit), the size of the duct channels so that the air flow is large. Maybe not...

For the wiring of the motor, note that the wiring for the Ender 3 V2 (at least mine) is a bit odd, in that wires 1+4 and 3+6 are pairs (not 1+3 and 4+6 as common for 6 pin JST). Took me forever to figure this out. You will also need to lower the...

For the wiring of the motor, note that the wiring for the Ender 3 V2 (at least mine) is a bit odd, in that wires 1+4 and 3+6 are pairs (not 1+3 and 4+6 as common for 6 pin JST). Took me forever to figure this out. You will also need to lower the...

Only 28G on 15%infill, compatible with Ender 3 v2. Preferred ABS od PET-G material. ... probe offset: X -45.00 Y -7.00

Crosslink did a remix for the Ender 3 V2 of 3D_LC's mounting plate. I didn't like to use the roller screws to mount this neither did I have any use for the cable routing channels as they can only be used for the fan and thermistor wires.</p><p>My...

Major changes are extra room for the hotend heat sink, bit more directional flow just below the top of the heat sink, and i added bltouch Print on its back with support touching build plate with 20% infill should work EDIT: V2 Added a recess for the...

... This should make probing very accurate. It only uses 1 of the BLTouch included screws for an really easy Mounting. The Mount needs 2 M3x10mm (DIN7991) Countersunk Head Screws. ... I prefer black filament and black screws for a clean look.

This is a remix of Tripp_2 fang plate with the addition of Madness1561 bltouch mount. This plate is meant to be used with the Smooth Fang by OzFungui. Clip is not included, just pick the one in Tripp_2's design. Esto es unicamente una mezcla del...

This is a remix of Tripp_2 fang plate with the addition of Madness1561 bltouch mount. This plate is meant to be used with the Smooth Fang by OzFungui. Clip is not included, just pick the one in Tripp_2's design. Esto es unicamente una mezcla del...

Bltouch support. Just fixed by the 2 small holes on the plate. No disassembly to do. ... I redesigned it because the one I had downloaded put the sensor too low compared to the nozzle.I moved it up 3mm.

This is remix of updated V3 version of 3DTouch/BLTouch holder by @jkostenov https://www.thingiverse.com/thing:4462870 Remix source file: `V3_probe_mount_less_fillets.stl` **probe offset: X-42.00 Y-10.00 (same as in original design)** #Variants#...

Micro swiss direct drive extruder fan holder for ender 3, ender 3 pro and ender 3 v2 with x-axis correction. This is two part body (part no. 1 and part no. 2), after printing two body must stick together with plastic adhesive glue. This is because...

I modified the Ender 3 V2 Direct Drive by JamieBK to fit for an aluminium extruder bought from AliExpress (search for "Ender 3 Extruder" and look for the red ones with orange springs). I used the same print settings as with the original one. ... -- ...

I printed with supports but used support blocker for the tubes directing air flow on to the nozzle, and also printed it in eSun PLA+, at 0.16 layer hight. ... please visit original thing at https://www.thingiverse.com/thing:4637453 or all other...

Added a provision for securing cables with 2 cable ties on to the Satsana body