ender 3 v2 direct drive with bltouch by5 3d models

... balance! V2 files have been added. For optimal results, use 1/4 x 1/8 PTFE for the idler tube and 3/8 mounting couplers and tubes for the short bowden run. ...Secure your setup with your preferred elastic material – I prefer to use elastic cord.

Remixed the duct to work with this direct drive mod (probably others as well) https://www.thingiverse.com/thing:4140659 I just tipped the blower fan forward a bit. I don't believe it affects the flow any. Requires supports for the base but nowhere...

I designed a test for direct extrusion on my Ender 3 without breaking the bank, utilizing only standard components and two extra M3 screws at a mere 25mm each. With this setup, I fine-tuned the retraction distance to an optimal 0.6mm. ... The long-term...

... cable to ensure smooth operation. ...Note that when using the direct drive system, filament flows directly into the extruder, but be aware that this configuration disables the filament sensor, which can cause continuous printing without interruption.

... for a dual drive extruder. ...For example these: https://s.click.aliexpress.com/e/_Asn5Xj * https://amzn.to/3aTCalG * The stock Ender 3 xxtruder doesn´t fit this besign because Filament outlet is 10mm higher. ... *These links are affiliate links

There are several Direct Drive mods available, but I wasn't satisfied with any of them. So I made one that <b>preserves the full original print area</b>. Even the full height can be preserved, but this would require a little thought in the cable...

Added pen mount for drawing on stuff. Pretty simple and oh so effective. ... Merge of : https://www.thingiverse.com/thing:4560739 and https://www.thingiverse.com/thing:3139205 Print the housing from SAWoosh.

Print as one piece, 40x10 fan face down. Press fit on the fan, bolt on all accessories as needed. See the original post on my page. ... https://www.thingiverse.com/thing:4630016

So this bracket fits the stock Cr-10s Pro V2 dual gear extruder and stepper and situates it directly above the stock hot end. Ive found that if you use just the hot end's ptfe capture nut (so not using the capture nut on the extruder) , it works...

Dieser Direct Drive Mod ist die Konsequente Weiterentwicklung der ersten Version. Für diesen Mod muss die Linearführung etwas gekürzt und auf der Stirnseite montiert werden. Mit dieser Anordnung wir der Kipphebel emliminiert und die...

Getting rid of the Bowden tube and turn your machine into a direct drive system. You will need two M3 x 12mm, to replace the two on the front of the hot end, and two M4 x 10mm screws and nuts to mount the motor. The mount from the motor is the...

If you're not familiar with the initial version, it was designed specifically for use in Infill 3D Deltas, although the project remains incomplete as of now but it will be completed soon, and updates are available on infill3d.com. The primary...

The advantages of this mount for Tornado, CR10, Ender are: - Hold the nozzle tighter by being closer - Integrate the hotend fan into the mount - Allow strong fans - blower for layer cooling - Easy release mechanism - Simple screws for assembly -...

Had a specific fitment issue with my DD Kit on the Ender3 V2. It is meant for the OEM Hotend with the Noctua Fan Mod. I Printed in .16 but I don´t think it matters too much. Print with Tree support but look for NO SUPPORT INSIDE of the part...

I remixed the Creality CR10s Pro Extended fan shroud (40x20mm fan) by plammers (https://www.thingiverse.com/thing:4814295) and my bracket is a perfect fit with it. *** You can use the stock one. ...Just use some washers/spacers to fill the gap ***

Printed almost all types of materials with this setup - TPU/PETG/PC/PET/ABS without issue, especially with TPU. Word to the wise: if you're experiencing start-up issues, your filament is probably damaged, cut it off and try again. If this is your...

I was really disappointed that the Ender 3 v2 Display does not work together with Octoprint. I stumbled upon https://www.youtube.com/watch?v=0JWddBiLQAU who explains how to use the old Ender 3 12864 Display on the Ender 3 v2 and decided to adapt it...

V2 of my original X carriage - still WIP for testing. I recently switched to an inductive sensor instead of my old capacitive one for ABL. The inductive sensor has a smaller detection range and my older V1 design had the probe mount too high to be...

V2 of my original X carriage - still WIP for testing. I recently switched to an inductive sensor instead of my old capacitive one for ABL. The inductive sensor has a smaller detection range and my older V1 design had the probe mount too high to be...

... the extruder assembly can be removed easily. &nbsp;The bracket is strong enough to not flex when driving hard.&nbsp;&nbsp;Remixed from a thingiverse part that was for an aftermarket extruderhttps://www.thingiverse.com/thing:3664172&nbsp;Good luck!

The fillet at the connection is removed, which will affect the installation of the connection 3. The position of M4 threaded hole is adjusted so that the pneumatic joint of the extruder and the nozzle can correspond The biggest advantage of this...

This is a modified version with a stronger part which clips to the metal plate and also an easier print on it's side with less supports needed.

This is a modified version with a stronger part which clips to the metal plate and also an easier print on it's side with less supports needed. ... Category: 3D Printer Extruders

https://youtu.be/GkMEGNlrSf0Distributed for archive purposesPrint SettingsPrinter:Neptune 2SRafts:Doesn't MatterSupports:Doesn't MatterResolution:0.2Infill:40-100Filament brand:OvertureFilament color:OptionalFilament material:PLA, ABS, PETGNotes:Just...

I added a vertical bar to support the attaching of the cables. ... I have mounted my spool on top of the frame. I have bypassed the filament switch with a short piece of filament.

I run this with a Hero Me setup but my mod of the Gantry adapter that put the hot end at the same distance as stock rather than -3mm of the Hero Me, my adapter also has extra air flow routes as I found the cooling was not great before. Printed...

I started with a Nema 17 mount plate https://www.thingiverse.com/thing:26126 and the x-carriage https://www.thingiverse.com/thing:4700359 and made this plate to sit on top of it and still allow you to use the stock hotend mount. You'll just need to...

Remix of this https://www.thingiverse.com/thing:4543524 But thingiverse won't link to it. Adapted for a Titan extruder or clone. I liked this mount for my stock extruder as it was really solid so made one for the titan, so its now mirrored to have...

BLTouch mount for Ender 3 Max

THE MOST CURRENT IS LOCATED HERE: https://www.thingiverse.com/thing:3965880 A NEW AND IMPROVED SET OF PARTS TO ADD THE TITAN GEARED EXTRUDER TO THE ENDER 3. I DESIGNED THIS AROUND THE TRIANGLE LABS "TITAN" EXTRuder (USING THE BOWDEN TUBE ADAPTER...