ender 3 v2 direct drive with bltouch by5 3d models

... Printed on Ender 3 Pro PLA at 210c, layer height of 0.2mm, layer width of 0.3mm, and 100% infill. ... Brim and support were used with support roof and bottom, touching the buildplate only, and the model was standing upright (cable mount upwards).

To build this incredible setup, you'll need the following materials: * Two M3 x6mm screws to secure the laser module in place * Four 25x10x3 magnets that will powerfully hold the laser mount in position * Two plastic screws designed specifically for...

A sleek fan cover for the Creality Ender 3 stock version: "Ender 3 air cap", crafted by the talented Andrea Persola from Trillogame. The design incorporates additional parts and modifications inspired by Filboyt's work [2912394], while the filament...

This adapter plate lets users take Akanar's Micro Swiss Direct Drive Hydra Fan Duct EZABL BLTouch design and use it with Creality Ender 5 printers. ...It merges the backplate from Akanar's design with Baird1fa's Micro Swiss direct drive adapter for...

This is a BLTouch mount designed specifically for the Ender 3.\r\n\r\nThe package includes an additional feature that allows you to attach an IL series Keyence laser micrometer on the opposite side.\r\n\r\nX and Y...

Tapa ventilador para https://www.thingiverse.com/thing:4789305 Dos versiones. ...Sin rejilla y con rejilla

This is a remix from https://www.thingiverse.com/thing:4731421 and https://www.thingiverse.com/thing:4637453

I installed the BL Touch on my ender 3 so i wasnt able to use the factory fan plate for the PCB. ...should be able to use all OE hardware</p> Category: 3D Printer Parts

I installed the BL Touch on my ender 3 so i wasnt able to use the factory fan plate for the PCB. ...should be able to use all OE hardware Category: 3D Printer Parts

I installed the BL Touch on my ender 3 so i wasnt able to use the factory fan plate for the PCB. ...should be able to use all OE hardware Category: 3D Printer Parts

Filament guide designed for the Ender 5 Plus direct drive conversion. ... V2 - Requires 1 M5x5 1 M5 cleat to mount V1 - Requires 1 M3x20 3 623ZZ bearings 1 M5x5 1 M5 cleat to mount

Cable Guide for Exoslide Direct Drive Mount

Ender 3 Direct BL Touch Setup and Calibration Guide Getting Started with Ender 3 Direct BL Touch To set up the Direct BL Touch on your Ender 3, begin by carefully removing any existing sensors or probes from your printer. Next, locate the BL Touch...

I could have simply used them straight up, but I didn't feel that just screwing them together with the two bottom screws would be secure enough, and I didn't want to connect them using screws. I considered merging them into one part, but it would...

... It securely clips onto the Ender 3 fan, providing a sturdy support mechanism for itself. To calibrate this setup, you'll need to adjust the X probe settings and Y probe settings within your firmware, specifically in the "configuration.h" tab.

I could have just used them straight up, but didn't feel that just screwing them together with the two bottom screws was going to be secure enough, and I didn't want to use screws to connect them. I thought about merging them into one part, but it...

A simple BLTouch Mount for the Bullseye Base Current status: I have only mounted the BLTouch but not tested it yet. My design comes in two versions: The normal version is the one I use myself, but has the disadvantage that the screw on the left...

My BLTouch (left of Petsfang) was bouncing into this so I cut out the section getting in the way. ...Did a quick modification in TinkerCAD if anyone wanted to get around this without cutting.

Please check out this model for BL-Touch support: [BL-Touch Mount](https://www.thingiverse.com/thing:3796136) I really like the [SMOOTH FANG](https://www.thingiverse.com/thing:3091560) since it is well made and can be printed without supports, but I...

Replaced the ball bearing in this https://www.thingiverse.com/thing:4683505 with a 3D printed gear bearing from here: https://www.thingiverse.com/thing:53451 Thanks to https://www.thingiverse.com/emmett and https://www.thingiverse.com/Markacho for...

V2 of directions tag for Ender 3 Pro. GCODE file will allow you to print it in 2 colours on Creality Ender 3 Pro and possibly on every Creality Ender series printer. ... Print as it is, with supports

... made a version for the MicroSwiss Dual Gear Extruder, but I like this one better. So I modified it slightly to mount the BLTouch. The offset is x58 y-9. ... If you enjoy this remix make donations to the OG designer so he keeps up the great work.

... and fit perfectly. ...But found that their is 2.3 mm eccentric between dual gear extruder and hotend (both the stock and metal). Hence herez the remix with +2.3mm shift of extruder on Y-axis. ... Many thanks to brats_wiseguy for fusion files

X Stop flag for use with the Creality BLTouch. ...Thinner body to ensure the flag is located in the correct place.

I didn't care for the way it flexed while everything else on the Ender 3 is solid. The problem is it only mounts solid on the fan mounting tabs. The rest of it is unsupported. My solution was to cut away the back side in Fusion 360 where it meets...

[Satsana Ender 3 Fan Duct](https://www.thingiverse.com/thing:4369859) with [Ender 3 BL Touch mount for stock hot end](https://www.thingiverse.com/thing:3557973) Offset: X-51 Y-12 It should stay clear of the x-axis end switch no problem, but keep an...

Mine has nozzle fan bit to the side as in original it wasn't going along with BMG Dual Drive. It requires minimal support - only in two places marker magenta on slicer screenshot. Same screenshot shows proper orientation for printing. It...

Don't forget to change your axes_map in the [adxl345] section of your klipper config to map the Z direction of your ADXL345 to the X axes or your resonance results will be incorrect. axes_map: z,y,x My resonance values after testing will not...

Fan mount for Ender 3 v2 with bl touch

Designed for Ender 3, Ender 3 Pro and Ender 3 V2. ...You can use with 625ZZ bearing with V-Slot.