ender 3 v2 direct drive with bltouch by5 3d models

If you want the whole Orbiter mount you can find it here: =========...

This is a remix of Hero Me V5 base 3 and stock extruder direct drive adapter made to fit Proper Printing's quick change adapter. You'll still need to download the rest of the required parts from the original designers. The default extruder stepper is...

Clearances were also checked at the printer's far right to ensure the BLTOUCH can probe the entire bed while avoiding interference with the stock belt tensioner. A small hex hole is located on the back of the fan duct for securing the bltouch mount...

Simple direct drive extruder, mounts on nema17 spacing holes. Version 2 is more durable. Version 3 has a motor spacer which allows the part that guides the filament to be printed closer to the mk8 bearing. It's really simple and I've been using this...

This is offset to be compatible with mistic100's replacement mainboard cover here: https://www.thingiverse.com/thing:3996114 The official Creality BLTouch upgrade kit for the Ender 3 occupies the same space as the mainboard fan, so the stock...

This is offset to be compatible with mistic100's replacement mainboard cover here: https://www.thingiverse.com/thing:3996114 The official Creality BLTouch upgrade kit for the Ender 3 occupies the same space as the mainboard fan, so the stock...

Mainboard cover for Creality Ender 3, originating from zb3k's original design on Thingiverse: https://www.thingiverse.com/thing:3619082. I relocated the fan 40mm to the rear, ensuring compatibility with the standard BLtouch adapter PCB. The side...

This is a remix to make the version for Ender 3 Pro fit the Ender 3 v2.

With this guide, the filament can move in a controlled way. ... It only has one piece, simple and effective

Parts needed: * 2 MK8 drive gears * 3 M3 threaded rods (120mm long) * 2 springs (trim shorter and use trial and error for tension) * Washers for M4 screws (to keep springs from slipping past screw heads) * Ball bearings (5x10x4) * Idlers with...

There are plenty of slots and holes for air to enter the enclosure, even if you have drawers on the right side of the Ender 3. The airflow coming out in this design is many times higher than what it was going in on the stock or vented designs I...

It has been adjusted with the original dimensions and the names of the segments are engraved in it . ...Now it's nicer and more organized to find what you're looking for or tell someone who doesn't know where to put it :)

This is a drawer for the Creality Ender 3 v2. It is not for the normal 3 or the Pro. ... The v2 normally comes with a drawer but mine was missing one so I made this to replace it.

The goal was use a Bondtech LGX extruder in a direct drive configuration with the Ender 7 Style dual 4010 fan shroud all mounted to a printermods MDD v1.3 plate with linear rail conversion. I am not an expert at 3D modeling so some filing and...

Backplate compatible with 3D printed direct drive brackets

Direct drive with BMG and piezo Orion, panc

light for Ender 3 v2 neoused Edison bulb filament with a resistor and connected to 5v and ground on the motherboard. ...likes would be appreciated.

I mounted the ender 3 v2 in an ikea lack, with the power supply outside the enclosure, so I needed to have the switch accessible in front part.

morel mushroom extruder knob for the ender 3 v2 I printed with just one mushroom should have used the two instead

I corrected the Z-axis pause points to be directly over the adjustment screws and also fixed the pauses so the Ender 3 V2 actually stops at each point. CHEP's original code doesn't line up on the V2 threads and just keeps moving without any pauses as...

This is a remix of Hero Me V5 base 3 and stock extruder direct drive adapter made to fit Proper Printing's quick change adapter. You'll still need to download the rest of the required parts from the original designers. The default extruder stepper is...

I designed this as the only other BLTouch-Mountable Ender 3 Fan Shroud had the BLTouch placed parallel to the hotend, not perpendicular, therefore taking more space. ... This version keeps the entirety of the hotend system within the x gantry...

created this to change the location of my control panel on my ender 3 v2

Simple bed corner holder for Ender 3 V2. ...It is designed for the original glass bed.

This is a support for Ender 3 V2 screen on the top of the aluminium extrusion.

i added an ender 3 v2 logo to MartinDubois's model.

Simple no chain pieces, no screws, no zip ties, cable management for the Ender 3 v2.

Кронштейн для подсветки Ender 3 V2. Для алюминиевого профиля на три полосы светодиодов. ...С заглушками

Tool holder that I designed to fit on the ender 3 v2 behind the control display

https://youtu.be/PcU10pR0DeM Ender 3 V2 Mainboard Silencer. ... Support: Yes