ender 3 v2 guide 3d models

My 2020 Ender 3 Pro features a red aluminum extruder, but the alignment between the filament exit from the guide and entry into the extruder was slightly off. To correct this, I shifted the coupler 3mm away from the Z-axis screw and down 2mm. In...

... Works fine with 1.75 filament. I haven't tested 3mm filament on this. Print instructionsCategory: 3D Printer Accessories Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: .3mm Infill: 50 percent

This is a filament guide for the Ender 3 Max for those who have opted to place their spools on top of the gantry. Other filament guides I've tried tend to be too low if you have anything connected to the z-axis screw (like a knob), so this one turns...

While going through the journey of getting the most mods and upgrades possible for my ender 3 pro, I've discovered a neat little filament guide. The thing that sold me was that the guide actually had a roller in order to release the stress from the...

Ender 3 Filament Guide Bottom: A Beginner's Step-by-Step Guide to Achieving Perfect Prints Every Time Introduction The Ender 3 is a popular and affordable 3D printer that has gained a reputation for producing high-quality prints, but getting the...

Ender 3 Filament Guide by Hand Whether you're a seasoned maker or just starting out, mastering the art of loading filament onto your Ender 3 can be a daunting task. Fear not, friend, for we've got you covered with this step-by-step guide on how to...

If you use PLASTIC EXTRUDER, please download the Ian's original version: https://www.thingiverse.com/thing:3085765 -------------------------------------------------------------------------------------- "This part can be mounted on the top of the...

Here is my take on a filament guide for the Ender 3. After seeing the design by Filboyt and using it, I designed my own version with significant improvements. The idler wheels prevent the filament from chewing through the guide, and the arm features...

This is a CAD model of the Ender 3-V2. This is the original modeling for the Ender 3V2 that is used by others and published on different sites. The measurements and modeling are made from my own Ender 3V2 3D printer which I love and it works like a...

This was designed for the Ender 3 Pro with the filament spool mounted on top. However, it can be used for any 20mm x 20mm or 20mm x 40mm extrusion because it is held on using two M4 t-nuts and two M4 x 18mm screws. The hardware I used is linked...

... one with the original length and another shortened by at least 20 mm. The shorter version offers flexibility when mounting the filament guide, even when the spool holder is positioned at its outermost end on the top cross-member of the Ender 3.

... turned. So I fabbed up a slip-on cap for the filament guide, and no more Evil Spool. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.20 Infill: 20 Filament: Any PLA Category: 3D Printer Accessories

This is a filament guide I created for my Ender 3. Unhappy with the existing options, I decided to design one that would meet my needs, and put an end to the frustrating problem of filament shavings dragging across the aluminum infeed. You can...

Here's a simple guide to get you started with your Ender 3 or other compatible 3D printers: Step 1: Unboxing and Setup Unbox your Ender 3 or compatible printer and carefully remove all packaging materials. Next, attach the y-axis rod supports to the...

feet for ender 3 35x20 Spool holder: https://www.thingiverse.com/thing:4721912

Guide for Ender 3 Pro, I wanted to design my own, so I'll share it with those who haven't found happiness among the many already existing ones. No support is needed, The axis goes in quite easily, just a little tap and it settles firmly into place....

Needed some feet for my Ender 3-V2 after upgrading the PSU fan and printed this cover for it : https://www.thingiverse.com/thing:4567153 These feet are simple and clean and fits over the rubber feet that are on the printer. There are two versions...

This is a DIY enclosure for the Creality Ender 3 V2. Printed parts list: (OPTIONAL) 1x hacksaw_block 16 x 4_mm_plexiglass_fixing 8 x 20x20_three_way_corner All other printed parts that is included in the download but not listed above is so...

This is a remix of the "halo" light for the Ender 3/V2. I created this with a taller wall and a more round shape, to prevent the LEDs from shining in my eyes, as my printer is places on a table beside me. For the wires to run in the channel of the...

I really liked the design Ender 3 V2 Scraper & Snips Holder from ahuczekdesign but I tend to use a glass scraper more than the paint scraper so I added an extra wide slot for that to fit snugly in to place I then decided that as I us the Needle nose...

This is a remix of the "halo" light for the Ender 3/V2. I created this with a taller wall and a more round shape, to prevent the LEDs from shining in my eyes, as my printer is places on a table beside me. For the wires to run in the channel of...

I built flat covers for my ender 3 v2. The fronts fit exact size. The back one fits with the motor and if you have only one motor in the back use the front one. it will be the same size. I did mine in silver then painted it. I added a picture of what...

I found that the original design's hole did not match up exactly with an Ender 3, I also wanted a more squared design.

<p>It works. ...I switched back to Bowden drive, because Bowden drive is better on a stock Ender 3 pro (circa 2022)

... ... After searching for a reasonably designed and easy to print filament guide, I have decided to design my own, which will satisfy my needs: 1. Making the arc from the spool to the extruder more smooth. 2. Guide the filament away from the Z-rod. 3.

This is a handy filament guide and cleaner I created specifically for my Ender 3 printer. Due to the abundance of dust in my print area, this tool helps keep it out of the nozzle, ensuring smoother prints. The cap clicks securely on and off with...

Français (English Below)_********************____********************J'ai toujours trouvé le Guide Filament de la ender3 un peu trop Basique et simpliste,Je vous propose donc ici une solution plus intelligente et fiable.Le filament passe par une...

With the Ender 3, the spool holder is normally mounted on top, creating a steep angle of entry, and if left unchecked will wear a slot in the feeder arm. The filament also rubs against the lead screw at the bottom. There are several solutions to the...

... a support block if you feel you need it.Clear out the hole in the pivot with a 3mm drill. I taped the hole in the main guide 3mm.Use a 3mm screw and nut . ... I superglued the nut to the screw after assembly.I hope you like it as much as my kitty.

This prevents the filament on the Ender 3 cutting a line in its plastic extruder. ...Just slide on the X-axis wheel mount and add any screw hook (eye, open eye or L-shaped).