ender 3 v2 guide 3d models

No screws, no supports, 608 ball bearing filament guide designed to fit in the Filboyt filament guide mount. Combine with thing:4683505 (lower) for a complete the set of no screws, no supports, upper & lower filament guides. ... In the pictures the...

...Supports are recommended/necessary in my opinion. Great filament guide if you have a side spool holder. ...Don't forget to print the 2 spacers and sleeve for the 608 bearing this mount uses, those pieces are found on the original post I remixed from!

Original model here: https://www.thingiverse.com/thing:3950799

-I reduced the hole of the support and the bearing fit piece to adapt it to a 3M screw. -I also lengthened the length of the adapter legs for the end of the V profile for more rigidity of the support. ... -Bearing remix from...

... got it to work. If you had the same kind of trouble, hopefully this one-part remix will help you benefit from the "BTT Smart Filament Sensor Mount Ender 3 V2" - and my thanks to pjm237 for the great work. ... **Prints without supports needed.**

I could not simply enlarge the model in the slicer, because that also made the distance between the holes greater, and it seems the tubing hole was too far away from the filament inlet anyhow (it seems it would have been off to the left even if I had...

Just a simple slip on filament guide for the Ender 3 series of printers.Designed to be used with a short section of PTFE, this guide will stop wear from filament rubbing on the extruder arm. ...It has been made to slip on with a tight fit so as not to...

Toolless / snap-on side filament guide Ender 3 V2. ...No fasteners needed, only 2 standard inline skate 608 bearings.

My attempt at another Ender 3 V2 accessory. This sits on your horizontal top rail and your lead screw. Additionally, the extra arm works as a filament guide. ... Enjoy!

I use this to help me reattach my Magnetic bed Onto my ender 3 v2 neo. ...I slide it on the Corner then place the bed over it aligning it and then remove it before Printing again

I have printed and tested this part on my personal Ender 3 V2 with Micro Swiss direct drive and all metal hot end setup. And it works great! Super happy with how it turned out. I hope you like it too! NOTE: I tried using the Remix feature for...

* If you want to print with cap, use the files Ender_3_V2_-_Runout_Sensor_Base.stl and Ender_3_V2_-_Runout_Sensor_Cap.stl, if not, use only the file Ender_3_V2_-_Runout_Sensor.stl. * If you use stock firmware, probable you will need to update it...

... the sensor. currently printing now. will make changes if needed and update. if you click the thingiverse link above you will see what kind of extruder i have. Printed on and for the Ender 3 V2. v2 is the updated one and will work perfect. ...

Eléments basés (mais redessinés) depuis les sources suivantes: https://www.thingiverse.com/thing:4185537 https://www.thingiverse.com/thing:4683505 https://www.thingiverse.com/thing:4695818 https://www.thingiverse.com/thing:4720152 This associated...

1 - M4 x 16mm bolt (spare part with my Ender 3, hopefully yours too). 1 - M3 nut, and 1 - M3 x 10mm bolt (optional - this if if you want to install the arm) Assembly (pretty straightforward): 1) Lay the ring on a flat surface and press the...

Print Settings Printer Brand: Creality Printer: Ender 3 Resolution: 1.2 Infill: 15% Filament: Generic PLA/PETG/ABS Black Notes: You may need cleaning the piece to fit the base and cap, depending of how much accurate your printer is. It doesn't need...

This Filament Guide and Cleaner bolts on to the lead screw guide on the X-Axis carriage, using the existing screws. It has cutouts to facilitate vertical movement of the carriage. Parts may need to be trimmed and/or sanded down as tolerances are...

This is a remix of Markacho project for Ender 3v2 printer with filament sensor. I change body length and fixing because when you add filament sensor you have different extruder holder. it comes in very tight so use some power to attached it. ...

Printed and tested on an Ender 3 using Simplify3D without any problems at all - it works great! Note: This is just one part of a set; you'll still need the other two pieces from the link above to complete the design. Note 2: I used 0.4mm for...

<p>This is a modified version of this thing <a href="https://www.thingiverse.com/thing:3052488">https://www.thingiverse.com/thing:3052488</a> by holspeed. In my case i've to feed the filament from the side due to space limitations. I just turned the...

Through hole size increased in diameter to 4.0 mmThickness of through-hole block decreased to 5.0 mmCable distance from vertical extrusion slightly reduced to better line-up with the hot-end mounted cable clip

My remix to be used with regular M5 hex screw that will be flush inside the recess.

This is a modified version of this thing https://www.thingiverse.com/thing:3052488 by holspeed. In my case i've to feed the filament from the side due to space limitations. I just turned the roller in a was that it suited my needs. ...You can find the...

La carrucola e il terminale sono quelli di @rosspayn3, ho modificato il progetto per adattarlo alla stampante con installato il Creality Offiziel Filament Sensor. ...Aggiunto anello per fissare i cavi

Ender 3 V2 adapter made for the Ender 3 Filament guide BY daGHIZmo. Fixes loose fitment on ender version 2s. ...When arm retaining screw is installed, expanding pins lock into gantry beam center-bore for tight fitment.

This is a simple filament guide for my ender 3 v2 using a PC4-M6 coupler and 8 cm of ptfe tubing. Perfect fit with my red aluminum extruder (not the dual gear one). Just a 25 min print on my ender 3 v2. ...

Filament guide for Ender 3 V2. Prevents the filament from touching the greasy lead screw. It is unlikely the filament would touch it but I think better safe than sorry. ... I changed the angle of the funnel and reduced the size of the lead screw shield.

After trying quite a few, this was one of the sturdiest filament rollers I could find for the Ender 3 V2 - so I remixed it to add a mount for my filament runout sensor too. Design is the same as the original, which attaches to the extruder via two of...