ender 3 v2 neo print quality 3d models

Had to make it shorter as I have a different screen mount on my ender 3 V2 which caused interference with the handle on this design.

My Ender 3 v2's spool mount was too big to fit small spools. ...This sits on top of the current spool bracket and easily added or removed.

Glue stick holder ender 3 v2 take the front 2 screws out and slide it in and put your screws back in

IP Camera support for Ender 3 v2 printer. ... I have also attached the OpenSCAD file if you need to fine tune it for your camera

Simple and strong filament guide for the printers: Ender 3, Pro, V2. Use support blocker where shown in picture. ... Release: 2.0

Tool holder for the ender 3 / v2. ...goes on the end of the 40/40 extrusion, in place of the cap.

This is a remix of Ender 3 V2 Riser Feet. I didn't have the orignal rubbers still there but I had 3mm rubber pieces around, so I decided to remix the feet. First I modified the height to be 35mm without any rubber, because otherwise it would be to...

Changed the original a bit for better fit, because my tolerances sucks Solid feet for the Ender 3 v2, problably other Enders/printers as well, fits all 40x40 profiles. ... 43mm high, 20mm wide, (20x20mm wide at the bottom).

I designed the part from scratch but measured the dimensions for the attaching part of the thing from another tool holder for the Ender 3 V2 (original spatula/scraper tool here: https://www.thingiverse.com/thing:4689265). ... Printing Tip: I printed it...

Wire strain relief on an Ender 3 V2 and Ender 5 Plus. Will work with other Ender machines. ... Best used with the Duke Doks V6 BMG mount: https://www.thingiverse.com/thing:4808299 Print with supports everywhere.

This a mount to convert your Ender 3 V2 to Direct Drive. It allows the stock fan shroud to remain and has a mount for the BLTouch. ...It mounts the stepper sideways so that it clears the Z Extrusion so that no printing area is lost

This is a replacement drawer knob for the Ender 3 v2 drawer. I suggest to print in PETG since it is more flefible and PLA will break when you push it in the hole of the drawer. //edit: Makers stated, that PLA will work without issues, thanks for...

Hi everyone, I wanted display on my Ender 3 V2 on the left side and because I didn't found any good I decided to design my own. It's easy to print. Display is in 45° tilt and for mounting I used screws from the original one. ... If you have any...

Screen wire protect, use with ENDER 3 V2 LH SCREEN MOUNT_REMIX (https://cults3d.com/fr/mod%C3%A8le-3d/outil/ahuczekdesign-32ca). You have STL and Fusion360 file. You can change parameter in Fusion360 to change anything. Print face to bed, and use...

With these parts you can install any 120mm Fan over your Creality Ender 3 v2 PSU and any 60mm Fan over your Mainboard. ...Fans will be mounted outside of Chassis, so you will need to print 4 of the included 30mm feet.

If you have the Ender 3 v2 Adjustable Screen Holder or the remix, and your screen is loose, you don't have to reprint the entire thing again. Print 2 of these wedges and install then on the screen posts, behind the adjustable screen holder. ...If it...

Replacement knob for the ender 3 v2 LCD. The original is small and flat, I needed something knurled, a little bigger and with a spot for the finger to rest for quick turning. Prints well upside down, shouldn't need support but just in case you can...

Spinning Spool Holder for Ender 3 V2, using parts that come with printer Allows the spool to spin freely, preventing issues with heavier spools being unable to feed into the extruder correctly Requires a 150mm M8 Bolt, 1 M8 Washer, 5 Nuts (Preferably...

This is a replacement drawer knob for the Ender 3 v2 drawer. I suggest to print in PETG since it is more flefible and PLA will break when you push it in the hole of the drawer. Category: 3D Printer Parts

Hotend cover for Ender 3 V2, printed for reason to replace standard cover and fan. Can mount 60x60 fans with dirrerent width. Mount with three standatd M3 screws and need one M3 nut. ... Need some hand work to align with roller M10 nut.

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...

BL-Touch mount for the Ender 3 V2. I made four version, two round screw and two nut head screw version. The print is support free. Probe offset for the firmware: X = -42, Y = -10 Z-offset is -0.96 for me. ... Additional parts needed : M3x6...

These are 4 separate designs of customisable extruder knob for the Ender 3 V2 base on the stock extruder knob. Designed in SolidWorks. Both STL and SLDPRT files are available for all. ... I suggest printing large side facing down as it eliminates...

This is a remix of:Ultimate Ender 3 V2 Nozzle Brush I've tweaked it so that you can print it without the supports and secure the brush with zip ties.Also, I lowered it a little because it would smash into it if you had ABL and did G29.

I made some modifications to be able to adapt it to the ender 3 pro and v2 or other bed with the same chassis. ... I strongly advise to print the model with a resin printer,the model requires a lot of details in the teeth.

Remixed version of the double led strip for the Creality Ender 3. Used this on my V2. Made the distance between the led strips a bit bigger to better spread the light on the print surface. ... Used the following led strip: ...

Just another filament guide for all Ender 3 models including Pro & V2. Looks similar to the existing guides like 3059604 from MattEllison, but this one slides smooth into place and rests flat on the top rail. To ensure proper printing you should...

Remixed By Mythical Now supports Ender 3 V2 Changes to the original - Leaves a small space at the back right of the part for the z axis cable that goes into the motor (see picture) Spaced back so the print is flush with the back of the z axis switch...

Some Ender 3 v2 printers have a slight offset on the z-axis. These spacers work for me. Feel free to remix. STEP file is there. Made this as a quick print. Just use a lot of bottom layers. Some might not need the vertical spacer. ...