ender 3 v2 neo upgrades 3d models

I extended the clip side to account for the overhang, and lengthened the left-most tab to catch.Extruder (Bottom) Mount: This came from a file on printables (https://www.printables.com/model/408734-ender-3-v2-neo-chain).Hot End Clip: This one is a...

... I'm not entirely sure if the dimensions of the profiles changed between the original Ender 3 and the Ender 3 v2 Neo, but at least on my unit, the slots in the profiles do not match the dimensions in the blueprints available from Creality on GitHub.

You can also raise the camera itself -after mounting it- for your liking.Print SettingsCreality Ender 3 V2 Neo - using Cura + Filament Friday Extra Fast 0.28 profile with 10% infill. Important: Print with a brim to help with adhesion. ...No support...

Remixed from https://www.printables.com/model/270817-ender-3-v2-extruder-cable-guide Supports needed. ... It's very tight

Ender 3 v2 led top and side led bar The installation was made with a 1 meter led 5050 strip

I've colour matched my LED to the one that's included in the Ender 3 V2 Neo CR touch to make it extra snazzy, Just screw mount the Raspberry Pi to the drawer base. I used recessed M2.5 screws that screw into a heat-sink from the bottom up. Then it's...

This holder fits the V2 Neo which comes with a stubbier small wrench (10.5mm handle), which will now fit. This holder should work really on any Ender machine and non other brands that have the same/similar rail. ... Note: For best finish print like in...

This support has been designed for those who, like me, own an Ender 3 V2 Neo and have added a Creality filament end sensor. Impossible to find on platforms so I designed a perfectly functional one. This pack includes: Stand The pulley The screw...

This is a direct replacement hotend cover for the Ender V2 Neo. It works with the standard fans only. It lines up with the blower fan intake better than the original. I added 4 LED's to the eyes and below to light up the print area. I use 2k ohm...

Modification of the E3V2 design to fit specifically the Ender 3 V2 Neo Recommendations: a) Connecting the autostop switch in parallel of the printer switch (i.e. ...connecting both switch pin to pin), and not serially (as suggested in the original...

All credit goes to the original creators - I simply added a couple features and modified them to fit my printer. This was designed for and tested on my Ender 3 V2 Neo with a Spider 3.0 Pro hot end. UPDATE: I started having issues with getting a good...

to jest rmix z opcją czyścika filamenty żeby nie blokował łożyska link do czyścika https://www.thingiverse.com/thing:3033662 Ustawienia drukowania Marka drukarki : Kreatywność Drukarka : Ender-3 v2 tratwy : NIE Obsługuje : Nie ma znaczenia...

I was tired of digging in the drawer for my Allen Wrenches... ...So, I made an Allen Wrench holder for the wrenches in the kit that comes with the Ender 3v2 Neo. ...Fit's on the top of the printer and is held in place by a T-Nut and a Cap Screw.

This is a moving camera mount for ender 3v2 neo. I created this to add a wifi camera to my setup to monitor prints. Print this in a lower layer height to make sure the quality it there for it to slot together. The end of the pin did break off for...

My Neo had a different bar layout to what this file required, so I modified the file slightly to fit. All other attributes are the same as the original file. ... You will still require a long ribbon cable.

I created this specifically to hold the UniTak3D Ender 3 3D Printer LED Lights found on Amazon here https://www.amazon.ca/dp/B0B7B1QG5Q?psc=1&ref=ppx_yo2ov_dt_b_product_details. I didn't like the way they just laid in the gantry rails so I made a...

this is mount works for the ender3 v2

I wanted a nice honeycomb / hexagon shaped control knob for the lcd on of Neo. Couldn't find anything to match @fedorSosnin 's Honeycomb Z axis knob. Sized nicely so it doesn't block the lower part of the screen. ...Slightly tight fit on the hole, but...

The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. This is a filament guide to help the filament enter the extruder at a better angle without...

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

Printed in PLA , 0.8mm top, bottom and walls, with 10% Gyroid infill Remixed with Ender tool holder slide-in-rail clip , flipped over to print flat and resized to 110mm away from gantry. NB works well, but slide in clip could do with some resizing...

I was searching a simple and easy duct for 5015 blower upgrade, lot of complicated designs out there. So I designed my own. It uses stock screw and attachments, doesn't mess with heat cartridge wires, and you have room to regulate distance from...

This is simple holder for memomry cards. ...It has one slot for SD Card, 2 USB slots and 3 microSD slots. ...It is mounted in the V-slots on the base.

I used a Nordlux Latona 4W white, a cheap led from my local hardware store. ... Size: 3,4 x 31,2 cm Where i bought it: https://www.bauhaus.dk/nordlux-lysarmatur-latona-4w-hvid

... ...I used original reel mount hardware to attach it to overhead gantry. I screwed the two pieces together for horizontal stability. the screw hole is 3.5mm. ...You can position the assembly wherever you like on the gantry to suit your needs.

Printed with: Ender v2 neo

ender 3 neo cooling dock for Noctua 40x20

Simple nozzle cooling air duct modification for Ender 3 Neo or Ender 3 V2 Neo, to provide improved and even cooling from all sides. ... Very clean and simple print with no supports needed This is a remix to fit Ender 3 neo printers from: DJIFF Edit:...

I couldn't find a Wyze V2 mount for my Ender 3 V2 Neo that did all the things I wanted so I made one. Attaches to the front with the factory screws. The actual V2 mount plate was made by jitterzPrintz and can be found here...