ender 3 v2 octopi 3d models

It just made for fun, but now you can decorate you Ender 3 V2 and other printers with a Z axis spindle with you favorite Lego figure or something else from Lego. SO if you BELIEVE that this will make your printer better, well then it for sure...

Since I built an enclosure for my Ender 3 V2 and had some space in the frame I made this drawer to store some more stuff and make the printer look a bit more clean. I didn't do a Knob yet, I was hoping to find one here. ... So this drawer is for the...

*USE PTEG FILAMENT OR YOU WILL HAVE ISSUES*If you make and add this to your printer consider leaving a rating and a make, thanks!A Nozzle Cleaner for the Ender 3 v2 Mounted on the bed, works with klipper firmware.To get to gcode macro for this part,...

First upload :) Adjustable camera mount for Ender 3 V2. Slides over Y-Axis tension adjustment for easy removal. Needs 2 M6 bolts with hex nuts. Hex nuts inset into assemblies. Part 4 holds the camera and allows for slight left and right rotation....

The power supply cover of the ender 3 v2 covers the vents, which is just nuts. A simple fix is to just remove the PSU cover but that leaves the AC wiring exposed to anyone who wants to put there fingers under the printer. This cover only covers...

not to replace them. --------------- If u use the [Ender 3 V2 Silent Pack](https://www.thingiverse.com/thing:4644985) then these (basic_Mobo_PSU_cover_30cm_V1.stl) feet, with this cut out at one of the edges, could be Helpful for you. ... ...

Just a Side Spool Holder is designed for the Ender 3 V2 because I didn't like the Spool being on top. Doesn't require any screws. It also also almost the exact width of a 1kg spool so it cuts down on side to side movement that the creality spool...

Direct Drive Extruder mount for ender 3 v2 direct drive holder for aluminum dual extruder. is wider than the classic by 9mm so download only for dual drive. ... to be sure, drill the finished holes with an 8m drill to make it easier to go inside ...

This part allows you to convert your Creality Ender 3 v2 to direct drive, without having to buy some expensive kit. You can safely re-use (almost) everything from your current setup such as motor and extruder. The only thing you DO need is 1 new...

great upgrade for an ender3 MKS Robin nano v3 available now I did this for v2 not sure about the changes on the board dimensions I dont think there are any case fan 60x60 Silent fan (Noctua/gelid) hot end fan 40x40 stock Ender 3 fan / v6 fan cooling...

Rebuilt/Remixed this idea specifically for the Ender 3 V2. Due to the closeness of the Z screw, the slot for the filament needed to be closer to the one side. I also liked the idea of adding some text to the top so I could print that in a different...

3D printable file for ender 3 v2 hotend. Only for stock fans used in the original hotend cover. The print cooling duct works fine but feel free to redesign it. Kindly use M3x5mm brass inserts and M3 bolts or stock bolts from the old hotend cover.

3D printable file for ender 3 v2 hotend. Only for stock fans used in the original hotend cover. The print cooling duct works fine but feel free to redesign it. Kindly use M3x5mm brass inserts and M3 bolts or stock bolts from the old hotend cover.

A simple L-bracket for hanging the PSU from an Ender 3 v2 underneath the table of a Lack enclosure. I made it thick enough to hold the PSU without too much wobble, but thin enough that you can screw the factory cover back overtop to help camoflage...

... like an ID card to keep wires pulled out of the way of the Z axis Or use it in any other way you might like....... ... I made this for an Creality Ender 3 V2, But it should fit on any printer that used the aluminum extrusion with the T slot. ...

... ...I made the base higher and turned it 60 degrees, so it faces the bed perfectly in an Ender 3 V2, without needing any adapters nor more parts. ...The Gopro Cage is open but holds the camera very tightly.

I made these legs for my Ender 3 v2. ... https://www.thingiverse.com/thing:4603075 I also made a fan cover for the Mainboard: https://www.thingiverse.com/thing:4612023 The fan I used was the Arctic F8: ...

... I'm using the calipers found at [this amazon link](https://smile.amazon.com/gp/product/B07DFFYCXS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1). They are generic brandless calipers. The spatula is the 38mm spatula that came with the Ender 3 V2.

Improved Z stepper motor mount for Ender 3 V2. Will let you adjust z stepper motor to the sides about 2mm and it has a 0.5mm spacer behind the stepper motor. You will need some longer screws to mount it to the frame and some short M3 screws to...

Included is a ready-made gcode for Ender 3 V2 temp tower for PLA. ...Bottom layer (below the test tower) is at 205 to ensure adhesion as print starts.</p><p>E-Steps are set for my extruder, change line 21 in G-Code to your extruder's...

This is a Stand for your Ender 3 v2 NEO stock spool holder. It uses it's original screws. I guess it might fits older models aswell?! I built the IKEA Lack housing for my printer so I had to remove the spool holder. With this stand you can reuse...

Fan mount for Ender 3 V2 (for printer with NO BL-touch). It is designed for a 60x60 mm PC fan (12v). I used: 4 - M4x30mm (cross type), 2 - M3x20mm (Hex type). The print is made with no support but i used a brim to fix it better to plate. For...

... Good for ender 3, v2, or any other printer that uses same profiles as Creality. Left side designed to be exactly same length as the aluminum profile, and right side sticks out a bit. 12cm in length, verify that it not interferes with the z axis.

This is an attempt on a Ender 3 V2 Neo x-axis cover. I needed it for a custom version later on , as a holder / bracket for a webcam. It turned out really well and fits as good as the original. ...Hope you might find a way to use it either as a...

My design of filament guide arm for Creality Ender 3 V2 before realizing there is entire industry of people making custom accessories for 3D printers :) Still, one might find it useful. ... A very simple single piece design with my own unique angular...

Support for the top of the Z lead screw for the Ender 3 v2 printer. Remixed from <a href="https://www.thingiverse.com/thing:4671947">this support</a>. It can be used with many <a href="https://bit.ly/2KPBxhU">knobs</a> designed for the rod of the...

This is just a remix of the feet with clip for the ender 3 v2 to adapt to the bigger rubber pads. So you need to print 4 copies for each corner of my remix + 4 copies of this one (choose the damper_feet_4040_-_A_-_without_...): ...

I received my new Ender 3 V2, and I designed this spool holder (its a copy of CR-6 SE) I have some issues in the holes for screws. I draw 5.25mm diameter for holes, for M5 screw, but the printer make some littler. The bigger part, took me 6 hours,...

EDIT: Now superseded by this design: https://www.thingiverse.com/thing:5330574 This is a bracket to mount the filament spool at the rear of a Creality Ender 3 v2. This makes the whole 3D printer footprint more compact and reduces the space required.

Mount for a camera on the end of an Ender 3 v2 X-axis arm. You can mount it either right side up, or inverted so your camera can be closer to the print bed. I edited the original model to use a camera screw to attach it vs. the webcam-specific hinge...