ender 3 v2 part cooling fan 3d models

I just created ender3 pro cooling fan blades (9 blade) with openscad (https://www.thingiverse.com/thing:689564). ... 9 blades hub-d : 22mm propeller d: 37 mm blade height : 6mm (but default 7.15 mm seems better, mein was a bit short) winglets off...

Ender 3 Pro parts cooling duckt fan 5015 Print Settings Printer: Creality Ender 3 Pro Rafts: No Supports: No Resolution: 0.14 Infill: 100 Notes: inspired from https://www.thingiverse.com/thing:2912394 https://www.thingiverse.com/thing:3563135...

For my Ender 3, I expanded the outlet from 2.5mm to 4.5mm and extended it by 2.5 mm, adjusting the source designs accordingly. There is still a 2.5 mm gap between the nozzle's bottom (or build plate) and the cooler's bottom. I also reinforced the...

Remixed for Ender 3D Printer from: https://www.thingiverse.com/thing:2357501

Remixed for Ender 3D Printer from https://www.thingiverse.com/thing:2387129

... for me, but when printing difficult parts with overhangs it was causing some issues. ...Figured out it was because the screw hole needed to be moved up and over to the left ~3mm. So remixed it and now it should aim the cooling fan much more accurately

External fan tip mounts offer a more open design, allowing for greater airflow and flexibility compared to traditional internal mounts. ...This setup provides a less restrictive environment, enabling fans to breathe more freely and maintain optimal...

The original idea credits go to EPF, who has graciously allowed me to adapt it for two Noctua fans. These fans come with cable snap-together clips, eliminating the need for soldering. Included are also fan covers. ...To complete this project, you'll...

I had a problem with the ears that hold the fan on the original so I added some reinforcements

This component cooling is based on the component cooling of the Neptune 4. It blows almost over the entire width of the print bed. It was designed for 4020 fans. The channel for the cables is continuous and can be easily opened on both sides of the...

Yet another fan guard for Ender 3 V2. I use it alongside my fan duct: https://www.thingiverse.com/thing:4754118 The inside cone is particularly wide to correspond to my front remplacement fan that has quite a wide center disk (12mm). ...I'd suggest you...

allows to support a fan at the wire entry, to avoid that it heats up too much on an ender 3 v2 equipped with a wire end detector... very appreciated when this one is in a box, because the wire became too malleable and thus bad drive... ...adaptable for...

A Fan shroud for the Ender 3 v2 to fit the “MBOT3D MK2 Remix (Ender7 style fan duct with dual 4010 fans)” - air ducts. https://www.printables.com/model/158236-mbot3d-mk2-remix-ender7-style-fan-duct-with-dual-4/filesThe front plate is made to...

A Fan shroud for the Ender 3 v2 to fit the “MBOT3D MK2 Remix (Ender7 style fan duct with dual 4010 fans)” - air ducts. https://www.printables.com/model/158236-mbot3d-mk2-remix-ender7-style-fan-duct-with-dual-4/filesThe front plate is made to print...

Drop in replacement for mouting a wider 40mm fan to the hotend of the Creality Ender 3 V2. Light and effective design made to fit with the original part cooling blower fan. I used the original mounting screws and needed one extra. ...For the fan i used...

Phelanp11's Mosquito Hotend mount is compatible with Creality CR-10/Ender 3 printers and also works seamlessly on Ender 5 models, but unfortunately, the part cooling fan cowl he designed does not fit perfectly. ...To resolve this issue, a revised...

The accessory is specifically designed for the Ender 3 and comparable models, attaching securely to the side of the standard extruder casing. ...Several similar designs are already available on Thingiverse, but this one raises the fan a notch higher,...

10-24-19 Update: Enhanced model features increased clearance within nozzle and optimized mounting holes for precise alignment toward nozzle.\r\n\r\nRecent adjustment since 10-9-19:\r\n-\Improved mounting hole clearance for added leeway in mounting...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

The human factor kicks in with a three-point cooling system. This system is printed using a precision of 0.1 layers, paired with an optimized infill density of 40%. ...The dual-shell approach adds a robustness to the design, ensuring structural...

This Thing is a fan mount that fits the stock Ender fan compactly to tkrneki's Chimera mount while still allowing enough airflow to cool the hotends. This makes it easy to install a Chimera without having to add any high performance part cooling...

https://youtu.be/dKNUsFJgSOQ Use glue or double-sided tape to attach (Silencer) to the bottom of the power supply (cooling fan hole)

I added an airduct for 40x40x10mm or 40x40x20mm silent noctua fans on the right side for part cooling. All mounting holes are diameter 3,8mm for threaded M3 inserts. There is a version with a box cutout on top for step down converters. The left...

Great-looking part cooling duct, secured with a clip to keep the fan wires in place. Printing flawlessly and all credit goes to Rocco81-92 for designing an excellent system. Visit https://www.thingiverse.com/thing:2751027 for the hotend duct and...

A BLTouch compatible part cooling 40mm fan adapter for Ender 3 that clears the belt tensioner screws. ... 40 x 20mm fan is recommended.

**Remixed hot end cooler for the Creality Ender 3 V2** Part list: **dual_5015_fang.stl** Remix of https://www.thingiverse.com/thing:2763931 (V3 dual 5015 fang). Please resize to 10% before slicing. I recommend an initial layer height of 0.12mm and a...

The shroud and bracket are required to mount it, and then wiring piece is optional if you want some cable management and also have a spot for a tiny buck converter for non 24v fans (front or rear ones):...

... This remix fixes several problems with the original design and improves airflow, which only cooled one side of the part. I added internal vanes to direct airflow all around the duct. The casing of the duct was reduced, allowing space for the LEDs.

CompatibilityEnder 6 with bl touch and adxl mount. xy offset:x_offset: -37y_offset: -8 you will loose some y build space.PETG preferredStandard supports for best qualityOther required parts/material8x magnets 6mm (diameter) x 3mm (thickness)a few...

So this edit removes the need for using a drill. Im not so keen in to drilling in to petg so this is the reason why i uploaded this model, hope it helps someone. Supports touching build plate. Print Settings Printer Brand: Prusa Printer: i3 MK2...