ender 3 v2 raspberry pi mount 3d models

Raspberry Pi Camera v2 case with a mounting arm for an Ender 3 V2 (also probably Ender 3) modeled as a mini security camera. Mounts to the bed using the leveling bolts. No extra hardware needed for assembly. The camera housing snaps together and...

My version is slightly chunkier with a thicker bracket that easily accommodates a Raspberry Pi camera V2.1 without the need for any support or rafts. This project requires just two M3 x 15mm hex bolts to assemble everything properly. To print the...

Raspberry Pi Camera Mount, slides onto the aluminium extrusion as shown in the images. Comes in three parts, Back of camera case, front of camera case and the mount itself. The camera case just snap fits together and allows room for the camera ribbon...

Raspberry Pi Camera Mount, slides onto the aluminium extrusion as shown in the images. Comes in three parts, Back of camera case, front of camera case and the mount itself. The camera case just snap fits together and allows room for the camera ribbon...

Remixed pi camera holder, which hides camera cable inside. ...Cable output is on inner side of printer (its good if rpi is hidden instead of drawer in printer).

I would imagine this works with other Ender 3s but I cannot confirm Note: Originally, I designed this to have studs that the board slides over, but those proved unusable because the ports needs to slide into the holes on the side of the case. So, I...

note that you'll still need the front face from https://www.thingiverse.com/thing:3525153 and the arm+mount from https://www.thingiverse.com/thing:3453624 to use this. ...I also remixed the arm to help it hold position better:...

#Intro This design is remixed from https://www.thingiverse.com/thing:4880836 and https://www.thingiverse.com/thing:3143662 This camera mount could mount on the X tensioner of Ender 3 V2, and there is an FFC slot for camera FFC cable management. The...

I Remix the Raspberry Pi 3 case from Lazax (https://www.thingiverse.com/thing:3892091) adding rails to use it in the Ender 3 v2 v-slot. Modifications: - Add v-slot rail to Ender 3 v2; - I removed the gaps from the bottom piece - Aligned the longest...

This is a remix of three modelsCamera bracket:https://www.printables.com/en/model/157687-ender-3-v2-gantry-adjustable-pi-camera-bracketCase:https://www.thingiverse.com/thing:1167846Camera bracket...

Raspberry Pi Camera v2 case with a mounting arm for an Ender 3 V2 (also probably Ender 3) modeled as a mini security camera. -- Arm piece is not compatible with BLTouch. See remixed arm for a compatible version -- 5 separate parts in total,...

Lets you mount a Raspberry Pi Camera module on the front of your Ender-3 v2.

Originally had a GoPro mount on it but I wanted the arm that held the Raspberry Pi Cam ribbon in it so added that mounted system to this So I loaded up Raspberry Pi CAM Mount with integrated cable management and Ender 3 / v2 GOPRO QR Camera Mount /...

This is a mount designed for the Raspberry Pi Cam V2 to fit the Ender 3 S1 as well as the Ender 3 S1 Pro. It is mounted on the front on either sides of the printer and gives a diagonal view on the print bed for monitoring over klipper / octoprint.

This print was designed to work on almost every ender 3 model and CR10 model.=======================================================================================================COMBATIBILITY:Tested: Ender 3, Ender 3 V2, Ender 3 V2 Neo, Ender 3 S1,...

Originally had a GoPro mount on it but I wanted the arm that held the Raspberry Pi Cam ribbon in it so added that mounted system to this you will need 4 screws to fit this onto your Ender 3 / 3m - 40mm Print Settings Printer Brand: Creality Printer:...

This is a case for Raspberry Pi 4 that is mounted to ender 3 v2 frame. Probably will fit any ender 3 and similiar printers. Case will fit the Pi, 40x10 fan with room for little heatsinks. I used 6mm heatsinks. There is not much room left after them...

This is a case for Raspberry Pi 4 that is mounted to ender 3 v2 frame. Probably will fit any ender 3 and similiar printers. Case will fit the Pi, 40x10 fan with room for little heatsinks. I used 6mm heatsinks. There is not much room left after them...

Here are the suggested modifications: - Reinforce the top and back plates for added thickness - Eliminate the cut-out hot sunk feature and add an abundance of ventilation holes - Convert the case back plate to a snap-on mount component that securely...

... The cutouts on the side are for cables which I have routed on the side through cable chain. Additionally needed hardware: One M3 nut One M3 T-nut (because the raspberry is covering the tapped hole) 2 Longer screws for front mounting points

Just took the nice 4040 rail design and enlarged it to fit under my pi 4 on my ender 3 v2. I left the plate full to fit multiple cases but for the canakit case, it's really easy to mark the holes through the bottom plate of the case to get a good...

This modifies [giacomo30196](https://www.thingiverse.com/giacomo30196)'s [Ender 3 Raspberry Pi 2/3 mount (UPDATED V2)](https://www.thingiverse.com/thing:3016364) rear/lower part to add a hole for a heatsink on the bottom of your Raspberry Pi. I had...

I pretty much like this Raspberry Pi Camera mount, but I did not want to mount it on the build plate due to the additional weight, so I made this mount base, to mount it on the aluminium extrusion next to the build plate. ... Print my mount base as well...

I pretty much like this Raspberry Pi Camera mount, but I did not want to mount it on the build plate due to the additional weight, so I made this mount base, to mount it on the aluminium extrusion next to the build plate. You can mount either on the...

### **This now lives on [Printables](https://www.printables.com/model/347670-ender-3-zaxis-camera-mount-for-raspberry-pi-camera) and may not be up to date on Thingiverse** Codemonkey1973's [Ender 3 Camera Mount for Raspberry Pi Camera...

A simple stand for Ender 3 Camera Mount for Raspberry Pi Camera V2.1 by Codemonkey1973. Best way to print the holder is upright, the bottom plate is best print laying flat. Print in PETG and without brim, the elephant foot of the holder should...

I used the Arm for BL Touch SLI and resized the file down to 9.99%. ...Corrected the scaling to match the original Raspberry Pi Camara mount Arm.

The Arducam Auto Focus camera I picked up didn't fit into the mounting plate, so I threw together one that did. ...This is the camera in question: https://www.amazon.com/dp/B07SN8GYGD

Print "standing" like you see on the cura picture (with build plate supports and brim only). ... UPDATE: V2 supports the camera (cable)

This is a revised remix of the original remix by Codemonkey1973, specifically designed to eliminate any remaining lettering from the flat surface.