ender 3 v2 reduce stringing 3d models

This is a piece for Ender 3 v2 PSU ikea lack enclosure. ...I made two pieces for easy printing Print Settings: 4 Walls 20 % infill Extra part needed: 4 head screw M3 x 8 mm PS:The prototype had to be modified (as seen in the picture), I...

... but bltouch will be mounted 3mm higher. ... Original worked great with stock Ender 3 v2 hotend, but I replaced it with all-metal one which is slightly shorter for some reason and bltouch probe collided with bed.

Full Aluminium bulldog extruder for nema 17 stepper motor and 3D printed holder, to develop my ender 3 v2 printer. 42x42x22 mm block size. ... I ordered from here: ...

This very simple clamp slips over the spool holder that comes with the Creality Ender 3 Neo V2 to prevent the spool from sliding off. Leaves just a little space between the end of the spool and the filament to allow the spool to spin. ... Inside...

... with the Aquila. ...I think the Ender 3 V2 has similar ones. Found the file at https://www.thingiverse.com/thing:4737883. ... It printed great, but I wanted a slightly tighter fit and I made the slope steeper to the tools aligned closer together.

... contribution. ...:) I made a IKEA (Type: L1324, 21777) LED-holder for Ender 3 v2 that slides nicely in to the V-frame. Brims was necessary or else it popped of from the bed. ... If anyone has tips and trix to make it better, please let me know.

This is a upgrade extruder arm for Voxelab Aquila and Ender 3 (V2) You will need extra hardware to mount the guide wheel as the original one is too short. It will fit the original spring. I have done a lot of prints since this upgrade and still...

I've designed an incredibly basic PSU holder specifically for my Lack table enclosure, which accommodates my Creality Ender 3 v2 Neo. It's crude and simple but it got the job done. The design allows for mounting the PSU under the table's top surface....

WyzeCam mount for Ender 3 V2. Mounts to the front leveling screws on the printer. I designed it with clearance but it ended up a little tight on the base of my WyzeCam, may need to scale it up a hair if it's too tight. ...Doesn't need any supports,...

wire support for my ender 3 v2 direct drive, mounted to the top of the enclosure and use a auto retract keychain inside. ... https://www.amazon.co.uk/gp/product/B0995YK84C/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 key chain used, just trim the...

My Ender 3 V2 Mother board is on the top layer so the fan was at the botton with little to no air flow so I made a duel fan holder to mount on the side using the 20x40 extrusion as support

This is a simple bed levelling design. ...The Gcode included is for the ender 3 v2 bed size. stl is included so you can change the size to your bed. Its one layer high at .2 resolution. takes about 5 min. ...Enjoy!

Spinning Spool Holder for Ender 3 V2, using parts that come with printer Allows the spool to spin freely, preventing issues with heavier spools being unable to feed into the extruder correctly Requires a 150mm M8 Bolt, 1 M8 Washer, 5 Nuts (Preferably...

BL-Touch mount for the Ender 3 V2. I made four version, two round screw and two nut head screw version. The print is support free. Probe offset for the firmware: X = -42, Y = -10 Z-offset is -0.96 for me. ... Additional parts needed : M3x6...

... haven’t printed yet if anyone wants to print and let me know i can adjust. ...`It should fit the screws that lock in the slots. I took the idea from this https://www.thingiverse.com/thing:2757810 design added it to this to fit the ender 3 v2. ...

Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. ... <strong>Probe offset: X-42.00 Y-10.00</strong> <strong>Thanks to...

This is a tool drawer for the 40x40 aluminium extrusion used on Ender 3 V2. Just remove the end cap and pop the drawer in. There is room for ten nozzles, nozzle cleaning tool, nozzle swap wrench and all the Allen keys that came with the printer. ...On...

These are direct drive mounts for Ender 3 V2. These mounts are for the default hot end. One is for the default single gear extruder and the other is for the dual gear extruder. ... To install, remove the spacers of the rollers, then fix the mount...

This is a replica of the control knob on the Creality Ender 3 V2. I basically just measured the original knob and recreated it, tweaked a few things here and there. I did this to make my printer more... colour co-ordinated :) Hope you guys enjoy! ...

#### CR Touch Mount for the Satsana Remix for the Ender 3 V2 I couldn't find a remix for the CR-Touch so I created it myself. #### Why? ... Because the original mount didn't have room for the connector of the CR-Touch, and if you tried to put the...

This cable chain mount screws into the Ender 3 V2 frame with M3 bolts. I designed it to be compatible with the common V-slot covers and also to be more in line with where the cables connect. ...Make sure to print it with the square part flat on the...

Fast print for easier turning of the factory extruder wheel for the Ender 3 V2. Designed with blender. Snug fit for the recesses of the wheel without additional fixings. The head of the crank has a recess for quick turning with the fingertip. ...

Tool Holder based on Mattwall model and designed to install in left side of Ender 3 V2. It include slots for screw driver, and fixed wrenchs than come with the printer. ...Additional slot was added to include a gauge thickness to calibrate the level in ...

The existing options were to mount to the 40mm extrusion, which is blocked by the PSU on the Ender 3 v2. My version attaches to the base of the machine using two existing screws and fits under the existing cable guide. You may need 3 or 4...

The existing options were to mount to the 40mm extrusion, which is blocked by the PSU on the Ender 3 v2. My version attaches to the base of the machine using two existing screws and fits under the existing cable guide. You may need 3 or 4 additional...

I designed the part from scratch but measured the dimensions for the attaching part of the thing from another tool holder for the Ender 3 V2 (original spatula/scraper tool here: https://www.thingiverse.com/thing:4689265). ... <b>Printing Tip</b>: I...

They are a straight fit to stock Ender 3 v2, have cut outs for the rear screws and plate area. Bottom outside of the feet flare out to provide are bigger overall footprint of the printer for better stability. The have a 2mm insert on the bottom...

My take on the squashball feet for my Ender 3 V2 I didn't liked the other designs on here and wanted something i could screw on instead of something that has a T-slot design integrated. For an Ender 3 V1 or Pro you can use 4x the front feet. For...

This motherboard cover is compatible with both the Ender 3 V2 and the Ender 3 Pro. Check out my Ender 3 V2 Silent PSU to complete the set! My remix houses an 80mm x 10mm fan that is mounted far away from the motherboard, giving you enough room to...

They are a straight fit to stock Ender 3 v2, have cut outs for the rear screws and plate area. Bottom outside of the feet flare out to provide are bigger overall footprint of the printer for better stability. The have a 2mm insert on the bottom of...