ender 3 v2 touch screen upgrade 3d models

Simple box for Ender3 v2 nozzle cleaning needle. The needle is very fragile and pointy. ...The box fits in the drawer This way you can take care of the needle and your fingers.

I made an extremely cheap Ender3 V2 enclosure using connectors I printed, painted 20mm PVC pipe (around $6 AUD) and some cheap sticking contact plastic. ...I also added some walls to help keep my cat out

Please take a look at [pedrolamas'](/pedrolamas) remix https://www.thingiverse.com/thing:4913020 This is part of my attempt for better cable management of the Ender3 V2 https://www.thingiverse.com/thing:4768402...

... available for the V2. The original handle scraped against the V2's belt tightener, so I just raised the central piece up a little higher. Finger grips nicely, and its nice and tucked away under the bed. Thanks to the original creator. ...

i modified this thing: https://www.thingiverse.com/thing:3589452 so it fits a bit better on the ender 3v2 on the orginal one its impossible to service the hotend and fans when it is installed

This is a nozzle holder for the parts drawer for the ender 3V2. It holds 12 nozzle's and the needle sits in the middle. ...At the top you can put the foam piece for the needle.

Unfortunately for now only a back cover is done - good to prevent trash getting inside if you don't mind the screen lying on the table :) The mounting square on the back is 31x31mm and 2mm deep, screw hole is 4mm. ... Small latch was added (but its...

Updates ------- • 2022.06.26: Ender 3 v2 mount added. • 2022.06.20: BLTouch & CR Touch Volcano hotend versions added. Klipper Firmware Notes ---------------------- My config below gives you a maximum bed size of 230x210 with ~5mm border on...

Small HSW module with attachment for Ender rails. I've put mine on top of the printer and holds bits and bobs nicely. ...And looks cool while doing so.Check out HSW here:https://www.printables.com/model/152592-honeycomb-storage-wall

The idea behind this work was to build a support for this type of sensor with something that directed the filament so that it does not touch the plastic part of the sensor and, also, does not need support for printing

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. This is a redesigned version of my other bracket. I incorporated more support on the "shelf" itself...

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. This is a redesigned version of my other bracket. I incorporated more support on the "shelf"...

There are 2 Mosfet Boxes, One of them is exactly under the table, you need to pay attention to ensure that it does not touch the table, if there is a space between the 40MM table, then it will be. On the other hand, the other Mosfet Box is under...

Cam Holder Cam 50mm PLA Nozzle 0.4mm Hight 0.2mm Bottom Layers 4 Top Layers 4 Walls 3

Cam holder Cam 50mm PLA Nozzle 0.4mm Hight 0.2mm Bottom Layers 4 Top Layers 4 Walls 3

My version of a very simple spool holder without use of ball bearings.Dimension : 5.3 cm x 4.4 cm x 4.0 cm

Cover to place fan 80x80x25 silent for ender 3v2, fits perfectly and has width space so that it does not rub with cables. this is a remake of another model in which does not fit a fan of that thickness. a current regulator is needed in case it is...

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.

This direct drive conversion for ender 3 pro. pacifically designed for cr touch. ...I made this in tinkcad.

Remix of ebyaskawa Ender 3 Pro Umbilical Support Bracket. ...I only added bl touch mount to it.

this a direct drive for a ender 3 pro with cr touch ( that my first try off publish thing )

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.

Petsfang Mount for CR Touch and Sonic Pad G Sensor ADXK345 for Ender 3 Pro using stock hotend plate

This is a remix of https://www.thingiverse.com/thing:4740512 I added a hole in the bottom to attach a fan to it. I also added some ventilation slots at the back. ...Furthermore, I split the parts for easier printing (simply glue them together).

... the print head. I used some cheap COB LED chips from dollar store flashlights and wired them up in parallel for use with any phone charger or any DC 5 volt power supply. I put holes for wires to pass through and 3 holes on the top for 3 zip ties.

... requires a standard M4 nut (not knurled). ... Directions 1. Print Both Pieces. 2. Insert M4 Nut into Knob align with hexagon pocket.. 3. Place Cap on knob. ... When I put this together, I didn't require any glue and the cap was very secure.

... and you only need to print 2 parts. ... #### Part(s): * 1x 680(zz) bearing. #### Printing: 1. Print the `E3V2_Wheel_608zz.stl` from the original mix. 2. Print this part (with support and 20-25% infill). 3. Snap/Press everything together. ...

... to go on the left side of the base. It uses the 40x40 V-slots. It has spaces for most of your day to day tools, and also has 3 Sd Card Slots in the rear. It has storage for nozzles or what ever you wish. ... The bolt scale measures up to 50MM.

This part has 3 goals: Contain the extruder led switch Hide cables Cable chains support It must be printed with the switches face down. This piece was designed to avoid the use of supports as much as possible. The only place where support will be...

... to go on the left side of the base. It uses the 40x40 V-slots. It has spaces for most of your day to day tools, and also has 3 Sd Card Slots in the rear. It has storage for nozzles or what ever you wish. ... The bolt scale measures up to 50MM.