ender 3 v2 vs ender 3 s1 3d models

This design optimization is for people who has cooling efficiency problem with his S1 and you don't want to add any weight to this super heavy Sprite thing.Since I found that the S1 has more stringing than the V2 has. I made some investigations and...

This design optimization is for people who has cooling efficiency problem with his S1 and you don't want to add any weight to this super heavy Sprite thing.Since I found that the S1 has more stringing than the V2 has. I made some investigations and...

Since I found that the S1 has more stringing than the V2 has. I made some investigations and experiments and found that the stock fan duct has a little bit deviated blowing direction. And I made an improved design that can significantly decrease the...

I added the following features- 1) Cutout for #10 X-acto knife 2) Micro SD card slot (micro card used/needed for screen firmware upgrades) 3) Hex print nozzel holders 4) Notch and hole for nozzle needle (just stuff a small piece of the black foam in...

Simplify3d v4 profiles for the E3 S1 Plus

You will have to snap the two pieces together they are fairly tight and will not come apart easily.Print SettingsPrinter:Creality Ender 3Resolution: 1.2Infill:20%Filament:Stronghero3D PETGBlack Notes: I Printed in PETG on a PEI bed but...

Remixed from Alex Watsons mount, his design made contact with the bed on my S1 Plus so I extended it and now it fits perfectly, I'm assuming that the S1 Plus extends further than the standard S1.

Hey, due to the new Ender 5S1 and its cooling tunnel, I also wanted something similar for the Ender 3S1 considering the original components. The part simply replaces the original attachment and is an alternative to it. The cooling tunnel was built...

... flat cable. ...Prevents end switch and X-axis motor wires from pulling and damage. On S1 Pro flat cable is a little wider and motor/end switch wires are shorter than on S1! ...That's why almost the same clips for S1 couldn't fit on S1 Pro perfectly.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/lpeB1rpPJZ9These are adapters to allow the S1 Pro LED to fit a S1 PLUS machine.

This design is based on fast printing time. ...The gcode file prints in 1h3m on my S1. Used regular PLA. ...

I remixed the design so it will fit for my Ender 3S1. Its snaps in the bayonet mount of the filamentholder. The 3D printed washers get between bearings and filament holder. ... Material: -15,5 cm long M8 threadbar -2* 608Z bearings, -2* M8 nylon...

When i sliced this i noticed the rail mount and bracket were not connected small fix but printed on my s1 and installed. ...cheers to the original maker!

I am using an enclosure with IKEA LACK. ...By default the S1 Pro display is mounted on the side. ...I made an adapter to mount it vertically because it is difficult for me to use.

Es válido para las 4 ruedas, imprimir 4 copias exactas. ...Mejor con PETG. Probados en una S1 Plus con ruedas de aluminio rojas. ...SOLO VÁLIDO PARA LAS RUEDAS ROJAS DE ALUMINIO.

Floated M3 nut for Ender3 S1 printer frame.Allows you to hold heavy things on the printer frame using M3 screw.Just easily slide the floating nut into the slot exist in the printer's frame.

This design serves three purposes: it provides protection to the exposed bearings for the z-axis screws (no dust accumulation, filament fragments, etc falling in), provides a filament guide for those that aren't using the on-body spool holder that...

It's a remix from https://www.thingiverse.com/thing:5953410, but much stronger because my cable is harder than on the regular S1 printer.And also on my design is lot more space for cables.But the idea of the original design was very good and now it...

I wanted a better spool holder design from my direct drive and i saw a s1 spool holder stl and ive remade it so it took less time to print and use less material. this isnt a remix ive done this from scratch using a similar approach to the...

This is a remix of a previous S1 Pro Camera mount and a flex arm camera mount that I meshed together to get more of what I needed. ... Original Mount:https://www.thingiverse.com/thing:5396885 Original Flex Arm:...

This is a Remix of the S1 Lightbar adapter. This should be a snug fit and require a couple of taps from a hammer or object that identifies as a hammer to seat in the end of the 2020 extrusion. ... The original adapter kept breaking at the bolt...

Although I've only tested this on the S1 Pro, it should also work on the S1 and the S1 Plus, as I believe they all share the same gantry design. You'll need either 8x 10mmx2mm or 4x 10mmx4mm neodymium magnets for this. As strong as you can get...

Work in progress. ... Remix from Creality Sonic Pad Mount. My tablet is Lenovo tab 3. Print parts separately to fit multiple lengths. Supports. 10 infill. ...0.4 nozzle.

An alternative tabletop mount for ender 3 S1 or S1 pro original spool holder. Can be used with diy enclosure or if you don't otherwise like original spoolholder placement. NOTE: you also need to relocate filament runout sensor. I personally used this...

Rotatable touchscreen for Ender 3 S1 and S1 Pro. The - Single.Stl files are editable files not the whole peace. I got sick and tired of the touchscreen being stuck in the same position so I 3d modeled a rotatable one so I can adjust the screen...

This is a remix of a previous S1 Pro Camera mount and a flex arm camera mount that I meshed together to get more of what I needed.Original Mount: https://www.thingiverse.com/thing:5396885 Original Flex Arm:...

Is splited in 3 parts for better print qualty. The cable for the nozzle fan is stretched to max. First looks like it's not long enough but falls into place while assembly. ... Hardware 2x M3x20 & 2x M3 Nuts needed The orange 4020er fan part on...

2023.3.6 UP DATE Added Rod riser clip 10mmRise ＆ 15mmRise Replace mounting bolts with M3x8mm bolts. Use M3x10mm bolts for knobs. The thickness of the mounting portion of the dial gauge is 8mm. Use extension rods. ... 【注意】 ...

This is my design for the Ender 3S1 Fan duct based on this design: https://www.thingiverse.com/thing:5238521The only difference being that there is no screw required (you will have to use the original screws that was used to mount the extruder), this...

This is my design for the Ender 3S1 Fan duct based on this design: https://www.thingiverse.com/thing:5238521 The only difference being that there is no screw required (you will have to use the original screws that was used to mount the extruder),...