ender 3 v2 x axis 3d models

Logitech C270 X Axis Mount for the Ender 3  & Ender 3 v2 There is a file if you have a BLTouch which also works if you do not have an ABL, and then there is a file if you have a CRTouch. In this remix, I fixed a printing issue from the original file...

Remixed the part with Slim X-Axis Chain Cable Support. Made with Fusion 360. ... Used with this cable links: https://www.thingiverse.com/thing:4314829 Enjoy :)

This design is to reuse the existing parts of the original tensioner, with subtractions in its four sides to reduce to its maximum the use of material, but at the same time to have a correct adjustment to the original parts.

This is a very basic change to the Ender 3 V2 Hot End Slim Chain x Axis Mount (https://www.thingiverse.com/thing:4569492). I was annoyed after breaking 3 or more prints of the original mount. So I thickened the tabs that always broke on me. This...

... cuts. I printed with 50% infill, for the extruder mount, but no need for that, i suggest 25-35% **Update 1. the Hotend mount have been lowered 5mm, to get the x-axis chain more level - new file - Hotend mount slim v2.STL*** - Hope you enjoy

Ender 3 V2 Hot End Slim Chain x Axis Mount K2 Hotend Slim Chain Mount Satsana.stl Satsana Version, for those using a Satsana Hotend Cover/Duct on Ender 3v2. K2_Hotend_Slim_Chain_Mount_SUV.stl: I used this original...

Ender 3 X-Axis Linear Rail Direct Drive Conversion V1 Notes: 1. Linear Rail Mount must be printed in PETG, ASA or a higher temp material 2. Linear Rail Belt Guide V5 is an updated right side X-Axis idler mount. Extra support to resist...

Ender 3 V2 Hot End Slim Chain x Axis Mount K2 Hotend Slim Chain Mount Satsana.stl Satsana Version, for those using a Satsana Hotend Cover/Duct on Ender 3v2. K2_Hotend_Slim_Chain_Mount_SUV.stl: I used this original...

I've used: https://www.thingiverse.com/thing:4878202 I've done mine in PETG and mounted on a Ender 3 V2 and it fits like a charm!!! This is not quite a remix, but more of an add on. Instead of using zip ties, I thought that was better to use...

... it longer as well. ... Also the camera case did not fit my v2.1 Pi-Cam, so I remix the case from [Ender 3 Pi cam mount by BartPLA](https://www.thingiverse.com/thing:3868687) and used the ball-connector from this design to allow it to connect. ...

original design text follows - https://www.thingiverse.com/thing:2987719 https://www.thingiverse.com/thing:4244869 remixed from https://thingiverse.com/thing:3147295 I had some issues with the original v2 camera parts, so I made some QoL...

a X-axis_rollers_cover for Ender 3 V2

a X-axis_rollers_cover for Ender 3 V2 Thanks to FilBer for the original :https://www.thingiverse.com/thing:4050465/files

If anyone requests, I can also upload a version without the X axis cable chain, but in my opinion, it works great. ...Maybe combine it with my other design here: https://www.thingiverse.com/thing:4787404 Slim links can be found from this link: ...

Humans now come alive with cutting-edge technology, reshaped by 3D Slash's groundbreaking capabilities.

... wing nut on the front-left corner of the BIBO bed. ... It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the back-center. Camera holder with casing for Raspberry Pi Camera v1.3 Ender 3 V2

This is a mounting plate I designed to fit onto an MGN12H linear rail carriage for the Creality Ender 3 x axis. I seated my linear rail right next to the limit switch so that the carriage activates the switch without falling off or exposing any ball...

This is a mounting plate I designed to fit onto an MGN12H linear rail carriage for the Creality Ender 3 x axis. I seated my linear rail right next to the limit switch so that the carriage activates the switch without falling off or exposing any ball...

{Please note this was tested and designed on an Ender 3 S1 Pro} Tools/Hardware Needed:Dial gauge - found on Amazon: “Clockwise Tools DIGR-0105 Electronic Digital Dial Indicator Gage Gauge"M3x8 ScrewM3 Nut (however, with the inner diameter used...

This is a remix of my previous design that works for the Ender 3 series of printers (not sure about the ender 3 max, if it has the same cap piece as the other ender 3 series printers it should work for it too) it's designed to allow you to watch your...

I wanted a mount for my Pi camera that would be mounted to the X-axis and offer a lot of flexibility for the camera angle. The popcorn joints can be assembled into an articulated arm that is mounted onto [Modmike's Cam...

Just a little remix to use the X Axis Belt Tensioner with an Ender 3 v2 with BLV Linear Rails upgrade. The 2020 Extrusion in the picture was shorted by 8mm. It will fit nicely for the stock length. There is a center piece for 5mm and 4mm Idler...

Just a little remix to use the X Axis Belt Tensioner with an Ender 3 v2 with BLV Linear Rails upgrade. The 2020 Extrusion in the picture was shorted by 8mm. It will fit nicely for the stock length. There is a center piece for 5mm and 4mm Idler...

New x-axis end cap for Ender V2 Neo printers to move the stop switch to a location that will work with the Creality Sprite extruder. You'll need two 6-8mm long M2 screws to screw the switch to the new cap. ...The cap is attached to the x-axis using the...

Motor cover, my QR sticker was looking worse for wear. So threw this together remixed from another users cover so that I can decorate better. ...Will put some paper behind for colour.

I uploaded a few versions, I haven't really found a good orientation to print the thicker revision. I made these pretty quickly w/tinkercad, perhaps I'll remake/re-remix them in blender or fusion 360 in the future. ... Currently using it with this...

<p>Just a simple extender switch I made because my fans were crashing into my frame before hitting the normal stop switch.</p><p>Update 9/10/22</p><p>Added a longer stop switch that is compatible with even larger printing...

Just a simple extender switch I made because my fans were crashing into my frame before hitting the normal stop switch. ... #DesktopInventions

Just a simple extender switch I made because my fans were crashing into my frame before hitting the normal stop switch. ... #DesktopInventions

Just a simple extender switch I made because my fans were crashing into my frame before hitting the normal stop switch. ... #DesktopInventions Video Link https://youtu.be/th__40wn7W8