ender 3 x axis cable chain 3d models

... only goes along one side and behind the stepper so that it does not block the Z-axis leadscrew. This will allow the cable and the Bowden tube to not need to be zip tied together, which will make removing the Bowden tube easier for maintenance.

#### Complementary Prints - Side Spool Mount with Wire Covers and Cable Chains: https://www.thingiverse.com/thing:5397466 - Filament Holder 80mm Spools Angled Remix: https://www.thingiverse.com/thing:5398018 - Ender 3 Pro Case Extended Raspberry Pi...

This is the upgraded cable chain v2, crafted by JohnnieWhiskey, which enables users to print an entire chain setup utilizing just two files. ... The original creator and image assets for assembly are courtesy of: ...

These pieces will help mount a cable chain on a micro-swiss direct drive extruder, all the way to the Z/X axis rear bracket (ender 3 pro) without sacrificing printing volume/area.All the other mounts I found had the cable chain binding on the side or...

Quick and dirty update to the cable chain tray for the X axis. Allows the trays to be used without the need to relocate the Y endstop. ...This replaces the right-hand (from front of printer) piece of the X axis tray.

I aimed to create a pulley/belt cover, but also wanted to incorporate a cable chain, so I merged the two ideas together with a mix of innovation and experimentation. After printing it out, I'm thrilled to report that it works flawlessly - but don't...

... a bracket for y axis. ONLY for cable to Y axis (bed) FOR CREALITY ENDER 3 V2 ( because there is a supply) There is an Ender logo (without a dragon) It has a reinforced bottom so that it does not break Print time approx. ...2 hours Well thank you

This Cable Chain does not limit any movent range of the Printer.I upgraded my Ender 3 and the following amount was needed:x-Axis: 12 Chain Segments and Clipsy-Axis: 14 Chain Segments and Clipsz-Axis: 25 Chain Segments and ClipsThis will improve the...

I found the Drag chain/Solid cable chains are a significant improvement over the standard "ender 3 cable chains".Download actual chain files here: https://www.thingiverse.com/thing:371500Installation of these chains is a bit more involved, but well...

To complement my existing johnniewhiskey set, I discovered that some Ender 3 Cable Chain adapters required modifications to accommodate the cubic frame of my Ender 5 printer. ...Consequently, I created a custom adapter to securely hold the Z-Axis cable...

... I made is fixed. I found with the Ender 3 Max that messing with the number of links for the Y Axis chain you will find the right number to give the chain enough free play to move and keep the cable in one plane as the bed moves back and forth. ...

Climb onto the steper and transport the cable chain to the z-axis location.

I realized I wanted to have a cable chain for the z axis and for the x axis, meaning I needed some kind of joint between them. With the newly freed spot where my extruder motor once was, I had the idea of mounting it there. Then I realized I had a...

This is a printable attach point for a cable chain supporting the extruder cord. ...It attaches to the Z axis feed motor with the screws already in place.

Just another cable chain for the ender 3. It doesnt work with the original extruder. Even if i would make it working, there is not enough space to handle it. But with Bondtech it works fine. Some others maybe too, but the original doesnt even...

Achtung: Es sind noch Anpassungen nötig, freue mich auf Euer Feedback Geänderte Kabelführung für den Ender 3 - Kabel für Extruder, X Achse und Hotend werden aus dem Mainboard Deckel direkt an den Streben nach oben geführt, nicht mehr unten durch die...

Update: It uses the angled heated bed mount found here: https://www.thingiverse.com/thing:3285566 It uses the z axis mount and slim chain links found here: https://www.thingiverse.com/thing:4314829 It uses the Rear Ender 3 V2 mount found here:...

This is a Y axis mount for the bed side of the Y chain made by diogosantos88 https://www.thingiverse.com/thing:3715002 and remixed by Tobi0892 https://www.thingiverse.com/thing:4316238 . I was using a chain made by johnniewhiskey...

The printrbot Model 3 has a horizontal cable chain for the X/Y axis - though it's fixed with two screws at either end (two at the extruder, two at the frame), I don't trust that it will stay level over time. Since this is a large-format printer, a...

X-axis cable holder for 3D-printer Creality Ender 3 and Ender 3 Pro with Sprite direct extruder. ...You need 2 pieces of M3x16 or longer screws and 2 pieces of M3 nuts.

This is the remix for https://www.thingiverse.com/thing:4322114 for slim x axis chains and common regular chains. ...This is WIP and have some mesh problems.

Cable Clip for Ender 3 X-Axis Modular Camera Mount Found Here: https://www.thingiverse.com/thing:4301899 Perfectly Suited for Cables Up to 3mm, Ideal for a C270 Camera

-------- This is a remix of the most popular X axis chain made by Fedor Sosnin https://www.thingiverse.com/thing:3132855 Go buy him a cup of coffee! After reading way too many comments about people printing their own links and in the end they were...

My printer has a longer X-Axis and they needed to be increased, hence i am not sure about the stock ender 3. ... Ender 3 bed size update to 315 X 235 mm: https://www.thingiverse.com/thing:4944833 Based on the original "Ender 3 raspberry pi camera 2.1...

UPDATE 02.27 - file motor mount.stl switched to a bondtech extruder and the old file didn't fit anymore so i made a 4mm plate to fit between the stepper motor and the extruder, stiffened up the chain mount too This is a remix of the most popular X...

Here's a detailed guide on how to create a custom cable chain system for the CR-10S 3D printer X-axis: This is a printable part that combines several components to form a functional cable chain. The design includes a total of 28 parts, which are...

I really loved Tobi0892's original X Axis Cable Chain Holder design, but still encountered problems with the plastic rubbing against the cables and producing some squeaking noises. I've remixed their design to use zip ties instead of chains for a...

Made a rough version that doesn't interfere with Z axis nut for direct drive converted setups. ... Currently using it with this: https://www.thingiverse.com/thing:4789619 Slim links can still be acquired from remix source: ...

This is my take on the X Axis cable chain and necessary attachment pieces. ... The image above outlines all the parts to print and direction for assembly.

This is my take on the X Axis cable chain and necessary attachment pieces. ... The image above outlines all the parts to print and direction for assembly.