ender 3 x axis 3d models

Just... ...Ender-3 X-axis Cover (Manual leveling hint included) .step - Feel free Remix! ...

Avengers logo for Ender 3 X-axis

Ender 3 X-axis cover (Atari) Rotate face down for printing

Ender 3 X-axis cover (Aperture Logo) Lay flat for printing

Remake of Ender 3 OEM x-axis stepper cover.

Remake of Ender 3 OEM x-axis stepper cover.

Ender 3 X Axis Endstop Cover Modified to allow the full 235mm X axis travel, it relocates the endstop inside the cover 5mm. ... Doesnt really require any further information than that.

Made this holder for an IKEA Dioder LED strip to mount to the Ender 3 X axis motor cover. Print both parts then glue together. LED should fit in and it will snug up when you push it further in. ...

Ender 3 X-axis mount for GoPro accessories. *** Original hardware will not work *** I made this to use the 2 screw holes on the x-axis cover that are left open with a damper. ...Shown here with yyh1002's Modular Mounting System...

Allows you to add a damper to the Ender 3 X-axis on models with a press fit pulley that isn't easily removable. You MUST flip the endstop switch PCB in the endstop cover (The part with the QR code) so the switch will still function in its new offset...

The original "Ender 3 - X-axis Rollers Cover" was created by FilBer his profile : https://www.thingiverse.com/FilBer the original piece : https://www.thingiverse.com/thing:4050465 The original piece hit always the motor support when it is back to the...

A remix of the creative Ender-3 X axis motor cover by Orseeny. https://www.thingiverse.com/thing:2921529 I modified the cover by removing some material and added some clips to hold the cover in place. I also added some material to parts of the...

I needed to push my endstop back after swapping to a e3d Titan Aqua and thought maybe others have the same issue so here is my Ender 3 X Axis Motor Cover with Adjustable Endstop. I extended the area for the mounting so as i can also tie off the...

**Creality Ender 3 X Axis Tension Tool** I just wanted a simple tool that would make it easier to install the pulley bracket onto the frame for the X axis. This is what I came up with. I printed it on a stock Ender 3 with no support and no...

Allows you to add a damper to the Ender 3 X-axis on models with a press fit pulley that isn't easily removable. You MUST flip the endstop switch PCB in the endstop cover (The part with the QR code) so the switch will still function in its new offset...

Thing Files helps you to upgrade Ender 3 x-Axis guide from original rubber bearing to MGN12H linear ball bearing rail. This Thing includes: - Track installation guide. Useful to center the rail to the X-axis profile - The belt anchor prolonger to...

This design was inspired by Ender-3 X axis motor cover by Orseeny - https://www.thingiverse.com/thing:2921529 and Dr Boo's Creality Dragon Logo - printable by DrBoo - https://www.thingiverse.com/thing:2873554 I decided to take it a step further and...

I replaced my Ender 3's X-axis limit switch. The original wasn't responding half of the time resulting in a stuttering motion. I used 2 M3x16 bolts and 2 m3 nuts. I used this exact switch:...

Decorative cover that hides the QR code on the x-axis cover of the Ender 3 v2. The original sticker is removed and the cover plugs into the screw heads of the original cover. The blank canvas offers a nice way to personalize your printer. You...

Always forgetting what direction the X axis moves so I came up with this solution

I created this little thing, to be able to use the x endstop of my ender, as i replaced the hotend carrier vith a Ender 3 V2 hotend. I printed it with an RF100 and Cura standard settings. Maybe this helps anybody, if not I will just use it for...

These are just some snap on trim pieces to dress up the Ender 3 or Cr-10.The motor side currently requires the X Pulley Cover.stl to be printed. ...I'll be uploading the STEP file so that people can modify it or take out that requirement as they see...

These are just some snap on trim pieces to dress up the Ender 3 or Cr-10.The motor side currently requires the X Pulley Cover.stl to be printed. ...I'll be uploading the STEP file so that people can modify it or take out that requirement as they see...

... profile. Here the belt runs parallel to the x-axis profile, and not diagonally upwards, unlike other tensioners. With the help of plastic card scraps, you can align the tensioner to compensate for the unevenness of the edge of the x-axis profile.

When performing a filament change mid print, you apply the clamp to the X axis pulley to prevent the hotted from moving. Works fine. No supports. ...My print came out a bit ropey due to settings.

The cover should be a snug fit and not move at all. Autobot logo: https://grabcad.com/library/autobot-logo-1 Unfortunately the Decepticon logo I found is no longer available, so I can't credit it. Print Settings Printer Brand: Creality Printer: ...

Simply slides over the X-gantry belt/endstop cover and provides a universal mounting locationIncludes a cable tie hook for up to 8mm wide and 2.5mm thick cable ties.Can easily be modified to fit webcams or lights; a blank baseplate is included in the...

This snap on cover is designed to hide the rollers than runs on the X axis. ... The model is compatible with Creality Ender 3 / Ender 3 PRO. ... Supports are needed for the clips.

Super easy to print cover for the x-axis pulley in the Ender 3, Ender 3 Pro and similar. No screws or anything, it just snaps right on. It's purely cosmetic and mildly protects from any contact or hits to the x-axis pulley. ... It's a Remix from...

The mount is integrated into the X-axis endstop cover which is included in the X-axis stepper motor damper mount files created by matthijsp. http://www.thingiverse.com/thing:3271077 Note that this is only compatible with the x axis damper plate in...