ender 3 z axis wobble 3d models

My attempt at another Ender 3 V2 accessory. This sits on your horizontal top rail and your lead screw. Additionally, the extra arm works as a filament guide. ... Enjoy!

Actual Z axis knobs to fit this are here https://www.thingiverse.com/thing:5147667 Z axis control knob. Revised design from original uploads. new base design prints better and looks better too. Gives users a knob to manually turn the lead...

The frame braces come from ProperPrinting, paired with a dual Z axis mod utilizing KFL08 Bearing Brackets. I chose to use the KFL08 because the 608 bearings were yielding poor results due to excessive slack and play between the bearings and the T8...

This small clip-on spacer provides ~2mm clearance between the wheel rim and the plate, and makes adjusting the Z-Axis corners a little easier without scraping the wheel against the plate. ... It also makes it a little easier to turn the wheels overall.

It's designed to match the height of the 20x20 profile and can be secured using a washer, an M5 hammer nut, and a leftover M5x8 bolt from the Ender 3 parts bin. ...Nevertheless, two additional M4 screws and their corresponding nuts are still required,...

After installing an adjustable Z motor mount, I had to recalibrate fafabienman's Z-axis guide (which relies on a 608 bearing) as it was now slightly off to the left by 1.5mm. Features -------- • Re-calibrated for use with adjustable z motor mounts.

... ...By incorporating three 22mm x 8mm x 7mm bearings, you can both solidify your Z-axis and steer your filament with precision. I have re-designed the knob to minimize its use of filament and shorten it, as the original obstructed my spool's rotation.

So I made this redesign that allows the Wheels/Rollers to turn freely.Print SettingsPrinter Brand:CrealityPrinter: Ender 3Rafts:Doesn't MatterSupports: YesResolution:0.16 or 0.2Infill: 55Filament: Generic PLA PLA White Notes:The OG model can be found...

So I made this redesign that allows the Wheels/Rollers to turn freely.Print SettingsPrinter Brand:CrealityPrinter: Ender 3Rafts:Doesn't MatterSupports: YesResolution:0.16 or 0.2Infill: 55Filament: Generic PLA PLA White Notes:The OG model can be found...

Remix of great Z-axis mount for a popular C270 webcam by @BKT_C5. My part of design is a little bit sloppy, because I was too lazy to do it from scratch and used piece of my own mesh for railing mount. See screenshot for how to place on the...

... my setup to fit my needs, ordering custom Tr8*2 POM Nuts from robotdigg that are bigger and have a distinct hole pattern compared to standard leadscrew nuts. ... My modified Ender 3 Pro now boasts dual Tr8*2 leadscrews, giving it a sleek new look.

I modified this for my situation, I ordered Tr8*2 POM Nuts from robotdigg, that is larger and has a different hole pattern than the usual leadscrew nuts. The pictured Ender 3 pro now has dual Tr8*2 leadscrews :D Category: 3D Printer Parts

No es más que otro diseño Esta es una adaptación para mi Ender 3 Pro, comprada en abril de 2020, una fusión de distintos diseños, este junto con uno del maker Tatamis45 de cults....

When I purchased the Ender 3 Max, I discovered a design flaw that caused the base to be very loose and therefore, reflected negatively on the printed parts. ... With this mod that I made from the original part, I lowered the end of stroke sensor by 4mm...

I was having some problems with my X axis sagging on the side that had no Z screw, so I purchased a dual Z axis kit and printed the parts to stabilize and synchronize the two Z axes.Here is the Timing Belt on...

Thin parts will bend easily, causing small increments in the axis to be ineffective, such as z-hop. A rock-solid part is now available. To improve stability, I recommend longer screws and an adjustable motor mount like this:...

If the Z axis is perfectly aligned and the v-slot wheels are adjusted precisely, the X gantry will gently fall into place with minimal resistance. This setup allows you to securely park the X gantry when the printer is powered off, and it will...

It's incredibly challenging getting two linear rails perfectly aligned for a Z-axis conversion. Most conversions only work because they utilize low-cost rails that have enough play to compensate for misalignment. As a result, this conversion focuses...

Just another cable chain for the ender 3. It doesnt work with the original extruder. Even if i would make it working, there is not enough space to handle it. But with Bondtech it works fine. Some others maybe too, but the original doesnt even...

the holder fits on the CR10S pro V1 and V2 as well as on the ender 3. on the printer no screws need to be replaced or loosened just slide it on and mount the camera. the camera housing for the PI V1/V2 you get here:...

Pi camera with IR Ender 3S1 Mount. ...See Original design for mount example

To use this mod you will have to be using the Belted Z-axis mod by Kenvinakasam, this is to be done with linear rails cable chains and a BMG style extruder mounted on the left hand side of the printer.This is the first iteration of this system and I...

... so just peel it off. - Made for an Ender 3 Max Neo but, as I didn't change the mounting point dimensions from Zotty, it should still work on other Ender 3 Models. - May remix again with cable routing built in if I can be bothered! ...

Z connector with slightly elongated chain connector and hole for cables

The two small screws are reused from removing the flexible base from the camera, and I used one random screw about 12-16mm long to hold the camera mount onto the clip / Ender 3 mount. Webcam:...

... the tensioning screw falls on, I made several versions. The thickness of the base plate is 3,5 mm. Print with 100% fill. I only used support for vertical through holes. Slicing program PrusaSlicer 2.6.0-alpha6, printer Ender-3 V2 Neo 0.4 mm nozzle.

the holder fits on the CR10S pro V1 and V2 as well as on the ender 3. on the printer no screws need to be replaced or loosened just slide it on and mount the camera. the camera housing for the PI V1/V2 you get here:...

I desperately needed a mount to securely attach my Nikkei extreme camera to the Ender 3 using a clip-on design, but an STL file was nowhere to be found online. With no other option left, I decided to take matters into my own hands and create one from...

I have only tried this on the  Ender 3 pro; other printers may have the holes in the correct place.To check your lead screw - move the gantry to the top (as seen in photo) and measure gap. Then measure the gap closer to the stepper motor. I had a...

I needed a mount to attach my Nikkei extreme to the Ender 3 using a clip-on, but after searching extensively, I couldn't find an STL file anywhere, forcing me to take matters into my own hands. Having only owned a printer since February 14th, I'm...