ender 3v2 3d printer

<p>Could not find one that i like and fit.</p><p>Cover with and without Voron logo.</p>

it connects to the non stepper end of the x axis bar, unscrew the tensioner then slide the model on the, screw the tensioner back on and then slide the camera in. ...make sure to print with support, i tried many different models but none suited my...

Made room for the spider hotend as it is wider than stock. Also extended fan ducts to match the nozzle. These are my values using cr-touch mounted with extra m3 bolts under the mount to reach under nozzle. Using mount from original project. ... ...

I now have a Direct Drive and I wanted a way to feed Filament from my Filament Dryer to the center of my top rail.

Tis is a simple clip to hold the ZXE cable to the frame, a little bit off cable management, simple and efective.

Customized version of https://www.thingiverse.com/thing:1169605 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1169605

I remixed this design with an extra height of about 4m to give the Notcua 80x25mm fan better fitting room. ...I also removed the buck converter mount because it is not needed with the Noctua fan.

Remix of DroneDaddy's mount to fit my existing setup from RaffoSan https://www.thingiverse.com/thing:2477180

This Model was created because I couldn't find a properly fitting nut screw for the Z-Axis. I personally love the small version, as it leaves some space for the thumb between the aluminium profile to pass by. ... contact me, if you require different...

Profile

null

Z Axis Mount Tripod/Webcam, slides on the right side of the Z Axis arm, uses a standard tripod 1/4inch screw to lock cam into place.

Edited Knob for a Embedded Nut with stop at layerhight command. ...

inspired by https://www.thingiverse.com/thing:4647053 The same part as BLTouch bracket V2 only with recess

End-clip requires 101% scale.

just print as is with your best print settings

Reduce +/- 0,20 Horizontal Compensation (VERY IMPORTAN)

Adapter has a frictionfit, dimensions: 51 x 35 x 11 mm

quite simple, so that you can see better in the dark where you have to insert the sd card. I printed it with glow in the dark, but it's too flat for that. ...It is best to print in a light color and cut out double-sided tape

Original direct drive from Creality came with plastic feeder , so I designed motor mount too use with my dual aluminum feeder.

this work in progress is a mix of https://www.thingiverse.com/thing:4559133 and https://www.thingiverse.com/thing:4545252 as I have the bl-touch original plate installed so I had to adapt the pen holder

With this you don't need to adjust table when changing print material, adjust just microswitch

Made an attachment for the bowden tube which came with de Esun Ebox lite filament dryer in Tinkercad. infill only in the tube to support the top layer with the smaller hole. ...(Tree support in Cura)

Remixed model with the following changes: - Solid and light versions - Removed upper profiles because they cannot be applicable if you are using moldings for alu profiles - Added two holes for original nuts to mount item fixedly

This is my small project. I very like Voron extrude but I wanted a more compact fan duct so I redrawn it Use M3x10 screws to connect the parts. ... No support needed when printing

Just made an improvement so the zstop has better repeatability and fast way to adjust it. I suggest to use the one without the screw holes. ... In case you use the the one with them, just put one on the lower part so it dosn't go below the intended...

I was looking for mount for this cable chains, bcs I didnt found any, I made my own.

Customized version of https://www.thingiverse.com/thing:4837562Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4837562

X-axis endstop relocation kit for linear rails. ...Loses no x-axis movement.

This is a remix of a remix , Original creation by Mattwall https://www.thingiverse.com/thing:3877505. My caliper had no good place to be, so I added a slot on the front face for a Calipers. It fits neatly along the bar causing no interference. I...