ender 3v2 board 3d models

Mount David Crocker's Mini Differential IR height sensing board on old style Creality print heads used on CR10/CR10s/Ender 3 printers and similar models. Visit https://miscsolutions.wordpress.com/mini-height-sensor-board/ for a detailed description...

I designed a rear electronics enclosure because I wanted to run 2 boards in my Ender 3 Pro. This relocates the boards and all associated wires to the rear of the printer. Wires enter the enclosure through the rear left. I added a cable brush to my...

Box for BigTreeTech SKR 1.4/Turbo board for Creality Ender 3 Pro/V2 printer with a cover with a lock or screws. ... A spring from a pen is needed for the locking version It is possible to use a 4010 or 4020 fan for cooling the electronics connected in...

http://creativecommons.org/licenses/by/3.0/ This remix solved the problem of the original 60mm fan cover not fitting with the pin27 board for the BLTOUCH installed. I took the original cover, shifted the whole 'hump' about 15mm backwards and...

Holder to mount David Crocker's Mini Differential IR height sensing board on the (old style) Creality print heads as used on the CR10/CR10s/Ender 3 and similar printers. See https://miscsolutions.wordpress.com/mini-height-sensor-board/ for a...

Holder to mount David Crocker's Mini Differential IR height sensing board on the (old style) Creality print heads as used on the CR10/CR10s/Ender 3 and similar printers. See https://miscsolutions.wordpress.com/mini-height-sensor-board/ for a...

... Brissfang fanduct. ... allows to use 40x40 fan for partscooling No need for using other hardware, only stock parts off your ender 3 printer. With BL touch mount. ... with cable arm holder Been running this setup on all my ender 3 for over a year.

This is an electronics enclosure specifically designed to house the SKR v1.3-board from Bigtreetech in an Ender 3 printer setup. It seamlessly replaces the original box while leaving sufficient space for cable management and accommodating large...

I got big heat problems with my "Melzi-Board" inside my "Ikea Lack" enclosure for the Ender 3. It can reach up to 40-50°C inside the enclosure, especially at printing with ABS!! And this is my solution for this problem! #Notes: - The grommet...

For ease of use, a switching board is installed, the basis is a 20x80 prototype board. https://www.chipdip.ru/product0/9000164294 Soon there will be an option for a 4020 radial fan for cooling radiators. For ease of assembly, a tap M3 and M4 is...

Ender 3 printer, equipped with a SKR 1.3 motherboard housed within its standard enclosure.

The fan opening is covered, keeping dirt and debris outside the main board area, as opposed to the original design which invites such messes into the precious main board space. The design was split into two parts for easier printing without...

The All Metal Hotend is 3mm shorter than the normal one (see pictures). So I shortened the Satsana as well. ... This is a remix of https://www.thingiverse.com/thing:4647053 Deutsche User: Bitte, wenn Ihr mich unterstützen wollt, schaut doch auch...

I wanted to mount the LCD Display using this awesome design by Otioss... https://www.thingiverse.com/thing:4753473 However to mount it to the right bottom aluminium profile you need to screw it in place. However not all of the profile holes are...

I remixed: https://www.thingiverse.com/thing:4647053 and https://www.thingiverse.com/thing:4780481 with each other 8 x M3 x 20 requiered for fan mounting

This is basically a work around for not being used to printing with PETG. This is a remix of the remix by Scrath_ of the Satsana fanduct by eric-anastas. Adding single layer connecting struts to connect all parts before the latter parts of the...

made a simple version that serves as a cap for 4 x 30mm M3 board spacers

This is a case for the BTT SKR Pro v1.2 to be side mounted on ender 3 (Left side) You will need to mount the stock ender 3 screen to this case since the wires don't reach the screen original location. I designed a cover but still need some...

It is compatible with the Creality stock or silent board, SKR Mini E3, and EZBoard Lite. If you any questions or issues, I'll be sure to answer them! Notes: • Print "Case No Z Cable Hole.stl" if your using a BLTouch or any other ABL sensor. • Refer...

This cover enables installation of a 50x10 mm fan alongside an SKR E3 DIP main board with TMC2208 drivers that come equipped with oversized radiators. The fan mount is positioned identically to the original 40 mm fan's location. ...Additionally, this...

When installing the BL touch there is insufficient head room in the compartment for the main board, thus this thing is a spacer which increases the head room of the compartment. ...Also after prolonged used the SD card slot may fail to remain in place,...

This is a derivation of MrTeliP original Ender 3 Pro SKR Mini E3 Case. He was gracious enough to make the STEP file available which made the editing rather easy. ...I removed the openings from the cover, as I didn't want filament to fall into the case,...

This is a derivation of MrTeliP original Ender 3 Pro SKR Mini E3 Case. He was gracious enough to make the STEP file available which made the editing rather easy. I removed the openings from the cover, as I didn't want filament to fall into the case,...

Relocate the Ender 3 Pro Control Panel Housing to the top of Printer to conserve desk space and provide more convenient access. ... This is a remix of the Minimalist Control Case from jckz82: https://www.thingiverse.com/thing:3127377 Replace the...

This is a modified Version of Marty_Z's Case https://www.thingiverse.com/thing:4790166 I needed a Case where my SKR2.0 Board, my RaspberryPi (aka Octoprint) and a DCDC downstepper (LM2596 for the fan) has space in. So i modified the Case... In the...

... case. Works great for using Klipper on a Raspberry Pi, Creality Sonic Pad, or anything else running Klipper. There is also an adapter for the Heated bed control board. It shifts it over and down so the leads from the control board are long enough.

... (by 0.1mm) if you prefer to use a self-tapping screw. Holes have been added so that the board could exhaust a bit more. Like the original author mentioned, please try to find a way to ground the board to your printer. ...Remixed with TinkerCAD.</p>

This upgrade takes Teaching Tech's idea to a new level by completely surrounding the board with an enclosure. The mount also accommodates the stock Ender3 board, using standoffs and bolts as needed. I have not tested this configuration but see no...

The Creality BLTouch Kit <--( I used this kit on my printer) causes Interference with the main board cover, this model aims to shift the fan over leaving room for the adapter board. <h3>Model Notes:</h3> This model uses M3x12 screws Holes are...

This part will protect filament and/or other items to fall and jam your board fan. I began making something with smaller intakes. After making several prints and measuring the adequate intake area needed, i came up with this design, which will use...