ender 3v2 program 3d models

I was looking for mount for this cable chains, bcs I didnt found any, I made my own.

Made room for the spider hotend as it is wider than stock. Also extended fan ducts to match the nozzle. These are my values using cr-touch mounted with extra m3 bolts under the mount to reach under nozzle. Using mount from original project. ... ...

It's a small remix to fit the weather vane onto the z axis. Done in tinkercad, as a learning experience. Printed without supports and infill 0.24 mm layer height. The model was glued together and sprayed with gold spray paint. ... It looks...

I need it, that I drew it and made it. ;-) Thrust me I'm engenier. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/j25jFTdkoNg

just print as is with your best print settings

End-clip requires 101% scale.

Customized version of https://www.thingiverse.com/thing:1169605 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1169605

This is a remix of a remix , Original creation by Mattwall https://www.thingiverse.com/thing:3877505. My caliper had no good place to be, so I added a slot on the front face for a Calipers. It fits neatly along the bar causing no interference. I...

This is my small project. I very like Voron extrude but I wanted a more compact fan duct so I redrawn it Use M3x10 screws to connect the parts. ... No support needed when printing

I now have a Direct Drive and I wanted a way to feed Filament from my Filament Dryer to the center of my top rail.

Made this display outline cover because I didn't want to print a whole screen case (too much red for the black&red theme I have). I ended up just making it flat so I could glue it on but I included a version that has a lip to sit on the case. knob...

Thanks to roblpetty for great source design. I took some of his advice and made the following changes... - moved the mainboard mounts slightly higher and towards the rear for better access. - filled in the top two lid holes - rounded off the...

With this you don't need to adjust table when changing print material, adjust just microswitch

Original direct drive from Creality came with plastic feeder , so I designed motor mount too use with my dual aluminum feeder.

Made an attachment for the bowden tube which came with de Esun Ebox lite filament dryer in Tinkercad. infill only in the tube to support the top layer with the smaller hole. ...(Tree support in Cura)

Reduce +/- 0,20 Horizontal Compensation (VERY IMPORTAN)

Original design worked as it should. Didn't like how mall the pick up knob was so i added a knurled knob. It is a bit taller and more tactile to the fingers. ...No other changes were made to size of cover, fits the screen tight and lets very little to...

Adapter has a frictionfit, dimensions: 51 x 35 x 11 mm

Remixed for the Pi3 and 40x40x10 fan. I just did a hack job on TinkerCad which works well for my use. I left the 4040 fan open so you can slide it up or down depending on heat sink. I thought I would have clearance issues but it was fine. ...I've...

quite simple, so that you can see better in the dark where you have to insert the sd card. I printed it with glow in the dark, but it's too flat for that. ...It is best to print in a light color and cut out double-sided tape

Wanted to fit a raspberry pi inside the footprint of the printer. Found the one this is mixed from, wasn't super happy with how that one looks, so I made this one to fit the heat sync and fan I used. ... I used these [90° usb cable...

original BL touch was mounted in a way that blocks the mounting to x carriage mount is from thingiverse making it difficult to adjust too toolhead i am also using cr touch mount comes from satana before using voron i was using this mount. ...thanks...

This is a small 130mm tall jig you can use to align the left and right side of your print head carriage when you use dual Z axis steppers. ...It slots into the bottom of the frame and makes aligning the axis a breeze.After powering off the printer the...

Another tool holder. Added some extra holes for scissors and nozzle cleaners ect. Added front container for holding screws and crap you don't want to lose when fixing your latest effing printer issue or upgrading something that completely does not...

Just made an improvement so the zstop has better repeatability and fast way to adjust it. I suggest to use the one without the screw holes. ... In case you use the the one with them, just put one on the lower part so it dosn't go below the intended...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

it connects to the non stepper end of the x axis bar, unscrew the tensioner then slide the model on the, screw the tensioner back on and then slide the camera in. ...make sure to print with support, i tried many different models but none suited my...

I made this holder for Ikea Mittled (40cm) led light 24v. I design it for M4x20 screw, mounted on top of printer with t-nut. It's slide from side to light frame. Printed on side. I made it with switch next to the screen. ... Hope some one will need...

Z Axis Mount Tripod/Webcam, slides on the right side of the Z Axis arm, uses a standard tripod 1/4inch screw to lock cam into place.

This Model was created because I couldn't find a properly fitting nut screw for the Z-Axis. I personally love the small version, as it leaves some space for the thumb between the aluminium profile to pass by. ... contact me, if you require different...