ender 3v2 upgrades 3d models

All the mounts available on thingieverse use the screw for the x wheel to mount it. I dont really like that, since we have 2 more holes prepared for that. Also this one is even easier and faster to print than all the others and fits with MiniMe air...

I am surrounded by Ender 3 V2s in my office and I wanted to see if I can find a way to make them look cooler, rather than be surrounded by a bunch of black machines. After searching for something already made and not finding anything I took it upon...

hi everyone this is the first upgrader that i thing will be good fro your Ender 3 skr 1,4 t tmc 2209 tft 3.5 v2 titan direct extruder and cable management (dsub 25 pin) for d sub you need to print it with nozzle 0.4 layer high 0.2 all the rest is...

... infill is recommended, with 100% on the duct. No supports are needed except for the direct drive mount. I always raft the parts. After the direct drive upgrade, you can reduce retraction significantly or entirely if you don't mind some stringing.

Includes a reprap 12864 display mount, drawers, Z rod knob, encoder knobs in 2 styles,a 4040 V-slot cap and a fusion 360 file for all of them. DISPLAY MOUNT IS WIP - You may need to tune the dimensions in the fusion file to match your printers...

Includes a reprap 12864 display mount, drawers, Z rod knob, encoder knobs in 2 styles,a 4040 V-slot cap and a fusion 360 file for all of them. DISPLAY MOUNT IS WIP - You may need to tune the dimensions in the fusion file to match your printers...

width 2mm

Remixed from both https://www.thingiverse.com/thing:4702089 and https://www.thingiverse.com/thing:3652452 I have modified the mount so the esp32 camera can mount directly to the camera mount

Work in progress. BLTouch mounted in the duct in line with the nozzle optimizing bed probing area. Probe offset x-0 y-42. Uses stock 4010 fans. Needs part cooling ducts, plenty to choose from on Thingiverse. ...Currently using these:...

I remixed this to work with the camera that I had for my raspberry pi. See [the original](https://www.thingiverse.com/thing:3586443) for more details and assembly instructions, except for the camera case. You will need to print the angled arm...

original sharpie blender https://www.myminifactory.com/object/3d-print-sharpie-marker-color-blender-3d-print-custom-colors-and-gradients-3-and-6-marker-version-138353

works for me, more text soon

<p>Small pillar support required at rear only</p>

Variation of my Tool holder remix for printers that have installed the 2nd. Z-Axis motor. ...Designed to clear the second axis

I needed an riser for the filament sensor because I had installed a dual gear extruder. I had already used the filament guide before and then adapted it for my combination.For stability, I recommend printing the filament guide/riser on the side as it...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Removed some extra material that was preventing the clip from properly sitting on the stepper motor. Since the motor has differing dimensions for the black vs silver sections, the original did not fit quite right. I also removed a portion of what...

I've designed this thing, to have the WLED plugin for OctoPrint showing the progress and what is happening (heating up, ready to print, cool down, idle). You could glue the stripe into the holder, but it's not needed if you also print the holder,...

I dont use the functions or screen much with Full Octoprint enabled never liked the angled bracket, So created a flat mount with access to sd card port for flashing without having to disassemble. ...

I was looking for mount for this cable chains, bcs I used other cable chain (but that was very bad) and I came to this one. There isnt any mount like this. ... It is suposed to be used with microswiss DD (direct drive), mount it (using 3 screw)...

This is a remix of the famous Satsana Fan Duct by eric-anastas, thanks for the great design to work with! I added an airduct for 40x40x10mm or 40x40x20mm silent noctua fans on the right side for part cooling. All mounting holes are diameter 3,8mm...

<p>Loved the simple and solid design that Mulilla made, but I found that the left locking tab was very delicate. &nbsp;I replaced the tab with a thicker tab, without the locking knob. ...&nbsp;The locking function isn't needed anyhow and now the tab is...

**Drilling new holes on bed mount plate is required, to use the existing holes the bolts would have to go through the linear rail carriage** This is a remix of a linear rail Y axis bed mount that I had on my E3 V2, with also having linear rails on...

<h2>Another design for a camera mount, but with a bed handle (silicone size), camera mount for the Raspberry Pi HQ Camera.</h2> <center>My first time designing and remixing a print, they are some common flaws, but fully functional.</center> ...

It won't let me tag, but also remixed from https://www.thingiverse.com/thing:4857870 I wanted a better design for the tool holder for dual z users, so I took it into my own hands! I changed it so the shears are put inside a sheath instead of...

Remixed the original 5015 fan duct and slimmed the left duct down to make room for the CR Touch Also added a slot for an M3 nut to utilize the rear mounting hole from the original duct

This is a modification of the Left Side BL Touch Mount for the BlokHead so that it's usable with a CR Touch. Depending on how things all line up for you, you'll need spacers to ensure the CR Touch is long enough. I used nuts and it works fine. ...

This is a work in progress let me know if needs tweaking it's not perfect

Notice that the main board was circulating hot air with the fan so close to the vents on the main board cover.

You will need a couple of M2 x 16mm screws and a bit of bowden tube (and some tape to hold the cover :D )Remixed from  https://www.thingiverse.com/thing:4337798  and https://www.thingiverse.com/thing:5382046