ender 5 fan 3d models

A fan duct for Creality Ender 5. It supports single or dual 5015 fans. I've used it for a while and it works fine. It's fairly easy to print and assemble. Should you break any part, it's quick to print again. It's not screwed on the backplate, it...

Wasn't really satisfied by the stock fan duct and thought I could improve on the existing alternatives on Thingiverse. I tried to keep the outlets as big as possible while preserving view on the nozzle. Fits the stock fan without the need to remove...

... attached takes into account of the 2mm, so it should work fine. No support is needed for this print. No extra screws needed. Work on stock Ender 5 parts. It takes a little time to adjust it into place because tolerance is a bit tight. ...

Successor of my previous design: https://www.thingiverse.com/thing:4363135 The air out lets are now symmetrically positioned around the nozzle and hot air coming from the hot end's heath sink is prevented from interfering with the model fan air flow....

Hello Have a nice day

... ... Its remixed so it will fit the stock Ender 5.exept for the fan mounting. I've made it a little wider to fit the cables from the hot end and removed the ABL mounting. ...I've put the text Ender 5 on the inlet and made vent holes on the side.

I couldn't find correct Creality spider hotend fan for Ender 5. So I remixed one. I printed the singel one version with bltouch and using it. I'm not a pro :) using thinkercad at the moment and will try Fusion360 soon as it is easy to change...

The inlet was modified to fit inside the fan, the mounts were thickened to properly fit the fan on the 5 plus, and the air outlet was moved 2.5mm so that it aligns correctly with the nozzle. ... This works with both a stock setup and Microswiss...

Hotend Kühler Halterung für Ender 5. Abgeleitet von https://www.thingiverse.com/thing:4369859 Funktioniert Super. Die Trenplatte ist um die Luftströme zu trennen. Damit lassen sich ohne Einhausung ABS und andere Schwierige Filamente drucken. ...Diese...

Print logo face on the bed. Print first layer the color you want. Pause after first layer then change filament color. ...Lower your Zoffset the height of your layer before resume.

Remixed an ender 5 plus fan duct to fit on my fan. ...The previous one had some extra plastic on that the screws go through and didn't fit on mine.

Ender 5 Pro - Fan Duck - Optimus V1 - one lump to rule everything, - easy assembly with 2 screws that are in the original cooling in Ender 5/Pro, - a special place for Bltouch, - suitable for original Hotend and Micro Swiss all-metal hotend, -...

Ender 3/5 Fan duct - this version has the steep overhang reduced to an approx 45 degree angle, making it a little easier to print. ... 2 versions available - one with a larger cap between the hot end and the bottom of the duct, and the other tighter...

Ender 5 Layer Fan Duct Remix for the Ender 5 Pro. Some Ender 5's have a different style fan which means these ducts need more or less screw structure. This remix remove the 'U' shaped screw holes. There is also a raised version that adds 3mm...

This is a layer fan duct I design for my Ender 5, it spreads the airflow all around the extruder. It should work on Ender 3 too. ... It is very important to have a silicon protector on the extruder, if not, this part can be partialy melted.

This is a layer fan duct I design for my Ender 5, it spreads the airflow all around the extruder. It should work on Ender 3 too. ...It is very important to have a silicon protector on the extruder, if not, this part can be partialy melted.

This is a 360° fan duct for the Ender 5 with a support structure, that benefits airflow. If you like/use my design, please consider to tip me. I'm a student and even the smallest amount is always welcome and appreciated. ...Thank you!

This is a remix of the Ender 5 Cooling Duct" by McGybeer. I removed the logo. ...Also on of the parts where the screws go thru didn't fit so I removed that too

The advantages over the original Ender 3 bracket: 1 - Visibility of the print on the plate 2 - Weight saving 20 grs instead of 50 grs for the original 3 - We keep the two fans and screws to reuse them on this assembly. 4 - The blown air comes out...

MINIMAL is a new fan shroud for Ender 5 with several advantages compared to the original one. It weighs 6 times less, the cooling fan is a bit higher so it cools only the heat sink and not the heating block and the new layer fan duct works...

MINIMAL is a new fan shroud for Ender 5 with several advantages compared to the original one. It weighs 6 times less, the cooling fan is a bit higher so it cools only the heat sink and not the heating block and the new layer fan duct works...

MINIMAL is a new fan shroud for Ender 5 with several advantages compared to the original one. ...It weighs 6 times less, the cooling fan is a bit higher so it cools only the heat sink and not the heating block and the new layer fan duct works...

I got fed up with the lack of focus the stock fan shroud provided and the downdraft on the part print from it #FittyJippy 0.4mm Nozzle max

This is a remix of the 40mm fan silencer I modified it for a snug fit on the hot-end fan. With my settings, print takes approx 10h - well worth waiting for the quality print at 0.12. Any mods welcome! ... Enjoy!

You do need to remove the PSU cover to allow the fan to do its work and, as usual with Noctua fans, you'll need buck converters to drop the 24v source to the 12v that the fans require. I left the 4020 PSU fan connected to act as a warning. It will...

If you dont like squeaking el cheapo stock cooler fan, remove that crap and replace it with hydraulic one with the same dimensions. This fan housing is light, it sucks air from above and therefore does not strings from your printings. The blower...

... For the BLTouch, the XY-Offsets should be as follows: define NOZZLE_TO_PROBE_OFFSET {-37, -16} There is now a new and improved version of the MicroSwiss DirectDrive Fan Duct for the Ender 5 available here: https://www.thingiverse.com/thing:4856649

I like Satsana Ender 3 Fan duct. It's easy to print. I use ender 5. It can't fit to ender 5 plate. because of belt lock position. Remix it. - I move fan to left size and change to 5015. - I add capacitive sensor. ... - dual glear direct drive.

DISCONTINUED: USE THE NEW V3 INSTEAD: https://www.thingiverse.com/thing:4975346 . . . This is a fan duct for an Ender5 using the MicroSwiss DirectDrive and AllMetalHotend to mount 40mm fans for part cooling and cooling the fins on the hotend. . THIS...

Description