ender 5 plus dimensions 3d models

TFT35-E3 V3.0 mount for Ender 5 Plus. ...You don't need any screws.

Ender 5 or Ender 5 Plus extruder cable support. This will help the extruder cable stand upright and not interfere with the printed objects. ... No screw needed.

Re angled the extruder mount to allow for attachment of ender 5 plus extruder with run out sensor. ...

casings to mount on a ender 5 plus for switches example: ventilator to cool heatbed after print or LED strip

perfect fit to ender 5 plus now with hols for air to come out of the printer

Klammer für den Filamenthalter am Ender 5 plus, damit die Spule nicht so rumeiert. ...Pefekt für Spulen bis 70mm Höhe

Ender 5 Plus tool holder. With bonus USB stick holder. The hole for the scraper may be a bit small. ...I modified the file from a CR10 version and don't have the actual scraper from an Ender 5.

Couvercles d'extrémité à utiliser avec le relocalisateur de barre transversale sur l'Ender 5 Plus.Modifié pour combler le trou en...

Clips into extrusion bar to hold up ender 5 plus hot end cablesZip tie cables through hole at the top to prevent them getting stuck

You can find my own control box design for Ender 5 plus. ...Feel free to make modifications :) Suggestion: 0.24mm, PETG

PLA Temp tower for the Ender 5 Plus. Speed: 60 mm/s Layer Height: 0,2 mm. Retraction: 1 mm. ... Acceleration: 250 mm/s2

Remix of the Satsana air duct to allow for the installation on and ender 5 plus carriage without causing a problem with the Y end stop or the belt tab. Pairs with my other file for installing the Mosquito hot-end onto the ender 5 plus.

Ender 5 Plus Tool Holder =================== Remix of https://www.thingiverse.com/thing:3655629 from [Kyle Finnigan](https://www.thingiverse.com/TrigoKlei). It's a tool holder for all Ender 5 Plus stock tools which can be clipped on the vertical...

This is a remix of the original mounting plate. ... This was changed to both give a better wire strain relief post and to allow it to mount on the Ender 5 plus carriage plate without hitting the left belt tab.

A simple block riser I put together to handle adding on NEMA Z Dampers to my Ender 5 Plus. ... This doesn't change the supported Z print area as it doesn't change the coupler configuration.

I didn't create this from scratch. ...The original work was done by dinesh612. They put in all the effort. My contribution was adding the Crealty Dragon and the Ender 5 Plus content to it.

Ender 5 Plus Filament Roller ====================== Simple "plug-on" Spool Holder with two 608zz (8mm x 22mm x 7mm) ball-bearings. ... It supports spools with a inner diameter of at least 72mm and a width of max 72mm.

This is an adaptable upgrade for the Ender 5 Plus featuring directional guidance to fine-tune your print bed, which can also be compatible with the CR-10S Pro.

Screen cover for ender 5 plus. Fits perfectly right in the ridge around the screen. ...I would print in black to completely block out the light but white filament makes for a cool effect.

This is a remix of https://www.thingiverse.com/thing:4548894 That was remixed from eric-anastas Satsana for the Ender 5 Plus. I added a taller wire strain relief and adjusted it to better fit around the belt protrusions. I have printed it and it is...

This adapter makes it possible to fit a SKR 1.4 board into an Ender 5 plus without cutting a hole in the case. ... Hardware required: 4 x 3mm screws When its printed, you take a 2,5 mm drillbit and drill the 4 four holes for the SKR board and the screw...

Filament guide for my Ender 5 plus, have my spool mounted on the side but the filament was making a 45 degree angle into the filament sensor. Not good. Made this to make sure filament enters at a more perpendicular angle. Mounts on stock Ender 5...

Originally it was remixed by https://www.thingiverse.com/thing:4548894 That was remixed from eric-anastas Satsana for the Ender 5 Plus this specific is remixed from remix created by PUCK81...

Ender 5 Plus Hemera Mount and Linear Rails https://www.thingiverse.com/thing:4163017 Remix of Sidewinder-X1-V2-Nighthawk V6 with instructions https://www.thingiverse.com/thing:4169959 Bottom Filament Feed for Hemera and Ender 5...

Simple design to cover the LCD screen on the Ender 5 Plus. I no longer use the touch panel on the printer, as I use Klipper. I added my own custom logo on my original print, but created a blank panel and one with the Ender logo to share. To get the...

The workbench I wanted to set my ender 5 plus up on was a bit smaller front to back than the footprint of the printer, so I made this doohickey. Just shove it under the feet along the edge of the surface it should accommodate the overhang. ... Use...

Pattern to see which corner needs to be set with Ender 5 Plus. Set your layer height to 0,2mm and you will have 2 layer. For bed equale or larger then 350mm x 350mm. ... *** WARNING*** Paper clip of the front left corner must to be move to...

Leveling feet for the Ender 5 Plus. A full set will require the following components: (2x) Part1-Mount-LH, (2x) Part2-Mount-RH, (4x) Part3-Foot, (4x) Part4-JamNut, (8x) M4x10 screws, (8x) M4 T-slot nuts. ... You can stick some foam tape or rubber dot...

... addition to mount LED strips facing to the print. ...Fits nice on my Ender 5 Plus. ...Maybe also on other Printers Before printing, lay it on the back in your slicing software to avoid support-printing Printing: Infill 10% Speed 100%

The Ender 5 Plus can be elevated by placing this foot under it, utilizing the stock feet provided. The foot features a tapered recess at the top that cradles the stock feet in place, preventing them from slipping or tilting. ...With this riser...