ender 5 plus electronics case 3d models

This adaptor fits between the Microswiss and the Bigtree tech runout sensor

Soporte para sustituir placa original al mover el extrusor y el motor para extrusion directa. Añado filtro limpieza filtro disponible en: https://www.thingiverse.com/thing:4348381 Support to replace original plate when moving the extruder and...

Made it sturdier and moved the bltouch mount to the right height x_offset: -45 y_offset: -6

Quick print. ...Created this because tube would get stuck there from them to time...

Disclaimer: I am not at all good at 3d modeling. I used Tinkercad to splice this up with some other mounting plate. ...Haven't tested/mounted it yet but it printed fine

This Spool Holder is adapted on a extended Frame of the printer, you must have 2 ball bearings APEC-7 608zz 8x22x7mm. ...You can mount it on the Alu Profile 20x20 with 3-5mm Slot T-NutsThe Frame Extension is made of Alu Profiles 20x20 Nut 6Alu...

I had an issue Regarding Cables set For Extruder, it was touching the printing BED.

Just run the gcode from sd or octoprint Use feeler gauge or paper while adjusting knobs

The higher the infill the sturdier the mount. ...I recommend 30%.

I created this remix to add in a CR Touch mount calibrated for a Revo Hemera on request. I'm currently using the Hemera V6/Colcano Part Cooling Duct by Hangtight but I haven't tested this CR Touch version as I have a BLTouch: ...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Improved version of original, removed gap that caused the ears to break easily, added chamfers and bevels to add strength, fixed some spacing issues and other small errors Screws still needed from original print

This is a mix of the direct drive mount from paydayxray (https://www.thingiverse.com/thing:4310609) and the hot end side link from Gnizten (https://www.thingiverse.com/thing:4116655)

These mounts are angled to solve clearance. The back one will clear my LED light strip and the front one mounts on the existing Micro Swiss threaded holes and clears the filament lever. I used 2 m3 screws to mount to the micro swiss and 1 m5...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I added some height and support to the cable doesn't drop/sag as much. ... This is a remix from https://www.thingiverse.com/thing:3937920

Bracket that holds the hot end cabling with cable ties, attaches to Y axis motor. ... Note: longer bolts needed or steal them from extruder run-out sensor (dimensions TBC 11/SEPT/2020) To be used in conjunction with: ...

This is conformed to work with the bullseye and the Santansa fan assemblies. I added a cable rest because my cable was just hanging down and being drug around. Gotta take care of the special parts. ...:)

This will help your rods being greased all the time when travelling up or down . the bracket will perfectly fit and slide over your bed and rod where you can ad a piece of foam keeping the rods greased and oiled all the time . 0.4 nozzle 0.2...

While the default BLOKHEAD mod will work with an E3DV6 hotend, I wanted to leverage my BMG Extruder in more of a direct drive setup. ...This is a remix of dpetsel's BLOKHEAD mod to allow for just that!you will still need to download the cap, fan, and...

Guida per Filamento PTFE in Direct drive. il connettore pneumatico è stato inserito scaldando la stampa e ammorbidendo la parte da filettare. il connettore è stato smontato dal slassico estrusore creality... quello che si sostituisce dopo 10 minuti...

Just a little cap to cover the Y axis switch pcb when using D_Jespersen's belt covers.  I printed it upright because it's a small enough space to bridge. ... Snapped right on, first try.

Slide it on like the pictures show. Orient the print like the sliced pic, no supports needed. ...Enjoy

<p>RPi Cam holder/mount. It is forward facing and rear mounted above the spool location. Swivels left and right and pivets up and down. ...2/M5x10mm buttonheads bolts with T nuts and 1/M3x40mm bolts for pivet.</p> <p>Works for me.</p> Category: 3D...

THis is a 6mm mdf and 3mm perspex enclosure Required - Hinges - 2 x 120 mm fans - mdf - perspex

Resolvi fazer umas capas de acabamento para esconder os componentes do eixo X. Se gostarem baixem e usem como desejar. ... Até mais galera!!

I don't have the hardware right now so I thought I could make a version that didn't need it. ...I have not printed this yet but please tell me if it needs to be fixed.

Filament guide for relocating the filament spool to the side of the printer. Attaches to the back extrusion with m4x10 bolts and t-nuts. Mine is setup on the right side, but it can be mirrored to place on the left side of the printer. ...

<p>Remix of <a href="https://www.thingiverse.com/macderson">macderson</a> design from Thingiverse</p><p><a href="https://www.thingiverse.com/thing:4255482">https://www.thingiverse.com/thing:4255482</a></p><p>&nbsp;</p>

Remix of GiulianoM's cooling duct to remove the duct on the side where the thermistor and heater attach to the cooling block (I had issues where the right side duct interfered with the screw-in high-temp thermistor I am using). I also cut off the tip...