ender 5 plus linear rails 3d models

I used the E3D Volcano mount to attach the Spider to the Ender 5 Plus. This allows you to position the Spider at the same z height as the stock hotend. You mount it upside down from the pics in the link: ...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. ...

The jetpack has been halved and will fit on an Ender 5 Plus bed and print without supports. To put the halves together I have added dowels and pocket screws. I've also put in some screw holes at the back and adapted the way the rockets are fitted so...

VIDEO: https://www.youtube.com/watch?v=RpIH-jXLHm8 ENDER 5 PLUS: https://bit.ly/2YHzpws BMG: clon:...

---------------------------------------------- This is an adaptation of my unpublished Ender 5 Duet Mount, modified for the Ender 5 Plus. It utilizes a 40mm fan (recommended: 24v SUNON 4020 or 12v Noctua 4020 via a buck converter) to direct air...

This is a bracket for the Ender 5 Plus controller case to move the cooling fan from the bottom to the rear of the controller case and cover the fan's old hole. The air will now be pulled in the front sides and exhausted out the back. The bracket...

Hello all, Here's an ajustable webCam support for Ender 5 plus ... or for all printers that has 2020 profil All the parts can be printed without support except for part 7. All the parts are printed mostly on the side edge so that the holes are...

This mount allows to use the stock extruder of the Ender 5 Plus to be used as direct drive extruder. Installation: 1.) Unscrew the fan chassis, the BL-Touch sensor as well as the hotend 2.) Disassemble the upper two mounting wheels of the...

A light bar for the Ender 5 + may fit the Ender 5 pro. Wide enough to hold normal LED's or the Neopixels. ... Wire holders on both sides so you can hold the cable.

Cover for the Meanwell Ender 5 PSU to go with the complete bottom cooling case. ... No supports needed

Remix of Ender 3 - Filament Holder Deluxe (https://www.thingiverse.com/thing:3114139) for Ender 5 Plus (tried to upload it as remix, but Thingiverse is not able to find the original design) - I was happy with the original design that I have used on...

The original part designed be Xerber https://www.thingiverse.com/thing:4727217 did not work with my Ender 5+, my Z rails are an extruded aluminum design and have an extra bit on the edge, instead of the flat bars pictured on the original design. ...

update 26.11.2023:added a version for an ADXL345 Sensor, for Klipper user.update 07.11.2023:I modified the left linear rail holder so that you can also attach a limit switch there, or as in my case, where sensorless homing is desired, a stop.I also...

Mountings bracket to relocate the stock electronics enclosure on an Ender 5 plus to the rear of the machine outside the frame. This re uses the stock bolts that held the enclosure in the frame and M4 bolts and T nuts to mount the brackets to the rear...

This is a filament lead in tube (Bowden) end holder for Ender 5 Plus direct extrusion modifications. It is designed to hold the end of the filament lead in tube from the filament break detector to the direct extruder. The filament bracket installs in...

I encountered a problem with my Ender 5 Plus in that the front was lower than the back even when everything else was equal. This led to rear adjustments being significantly tighter than the front and became an issue when I switched to solid silicon...

Aluminum LED Channel brackets for the Ender 5/ Plus printers. You will need to print two of each file for all four needed. The brackets do not have holes for the wiring, but 10 seconds and a drill bit will put the hole wherever you want it. ...

This is a Ball-Bearing Filament holder for Creality Ender 5 Plus (or possibly other models) designed to accommodate filaments weighing 1000g or less with an inner diameter of 52mm. To complete this project, you will need two sealed ball bearings...

Since uploading my Ender 5 Plus Micro Swiss cable support bracket, I have redesigned a bracket to fit at the end of the X Gantry to mount the cable on to support it away from the metal frame and the wheels on the gantry. You will need to install...

One was for Ender3 and the other was a rough Ender 5 Plus design that needed jesus. This should be usable with the Ender5+ with little to no modifications to your printer. It uses the default hardware. BLTouch mount is about 5mm to the left of the...

...My design has been put to the test on my Ender 5 Plus printer, which operates seamlessly without any hardware holding it back. To accommodate varying bed thicknesses, users can fine-tune their designs using the scale feature in the slicer software.

This extend your Ender 5 Plus rubber feets by 35mm. (I need this for my own silent cooling solution, maybe I will show you later). Maybe you like this too to add more airflow to the Z stepper motors. You need 4mm brass inlays, so you can reuse the...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications.It bolts on from inside using the original mounting points and screws.You mount the LCD to the back cover first with the M4 screws and nuts,...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications. It bolts on from inside using the original mounting points and screws. You mount the LCD to the back cover first with the M4 screws and...

I created a mounting bracket for the BigTreeTech PiTFT50 screen to fit on an Ender 5 Plus. The design is in 2 parts (plus the retaining clips). Because of the way it's designed, you can still mount the Pi on the back of the display if you wish.</p>...

If your printer uses the same carriage plate that the ender 5 plus does then this should work for you too. This uses the stock BLtouch mount and you can use the stock 40mm fan but if you want the cooling fan you'll need a 5015 blower (I have not done...

My take on the low friction spool holder designed to fit the Ender 5 Plus bracket. It ended up being too low friction and would spin on its own. ...I added some foam between the spacer and the spindle body, which resolved the issue. Required Hardware:...

Decided to go another route, but if I had kept it I would've reprinted in PETG.Printed great on my Ender 5 Plus, I added 3 perimeters(for a total of 6) and 10% infill(for a total of 25%) for some added strength.Print SettingsPrinter...

I created a mounting bracket for the BigTreeTech PiTFT50 screen to fit on an Ender 5 Plus. The design is in 2 parts (plus the retaining clips). Because of the way it's designed, you can still mount the Pi on the back of the display if you wish. ...

This model is designed to fit a Vizio xr6m10 tablet (5.5 x 3.5 x 0.2 inches), but you can easily update the model to work with other phones/tablets by tweaking the [Tinkercad...