ender 5 plus modifications 3d models

Spool Holder Parts Required: qty 1 - 3/8" x 5" Bolt qty 1 - 3/8" Nut qty 6 - #6-32 x 1/2" Socket Head Cap Screws qty 2 - 3/8 ID x 7/8 OD x 9/32 width Pre-Lubricated Bearing (I use these because I always have some on hand)...

This is a mounting plate to put the BTT TFT70 on the lower right front corner of the machine. I got fed up with not having a place to put it, so this solves my issue. I printed in PLA for the draft that you see in the photo, but you may want to...

A human requires an additional module to be installed.

for SKR2

I made it almost 1 to 1 with small changes. it works since the replacement perfectly. ... Be sure to print it with 4 lines for the wall and 50% infill for a longer lifetime.

I remixed the previous version which was not centered with the nozzle. I corrected the nozzle relief placement. I then made another version with cooling capability around the entire nozzle using a full circle air duct. I had some issues with the...

I designed this case to move the Original screen outside the enclosure to make room for an SKR E3 Turbo mainboard. ...I used on the inside a mount from Thingiverse https://www.thingiverse.com/thing:4676133

Mounting plate adapter to use microswiss direct drive plate with the exoslide system To mount remove exoslide, mount plate to exoslide then mount plate to microswiss plate then mount exoslide back on rail

Relocates the Y axis stop sensor to the back rail to allow for horizontal movement for exoslide plates

This is a remix of: https://www.thingiverse.com/thing:3842765, but it woudn't find it when I checked remix... This adds the option to use the front mounting holes to secure the screen enclosure. I also added a large lip to the back underside with the...

<p>Parts Required: (I used Socket Head Cap Screws)<br>qty 6 to 10 - M3 x 6mm screws&nbsp;<br>qty 2 -M5 x 8mm screws and T-nuts<br>qty 2 -M3 x 8mm screws and T-nuts</p><p>You might need to move the bundle holder up a hole to clear the end stop</p>

0.2 layer height supports: yes mounts to back of lcd screen with stock bolts make sure you replace the ground fork

# I'll be updating this shortly with the parts list and more details # ### Why? ### This started because I wanted to use the Bondtech extruder as direct drive with a v6 as it was intended. This was before the release or talk about the Micro Swiss...

just a quick remix sorry for poor skills hahaha

I noticed that the original wire clip design was prone to popping out of the extrusions whenever someone merely touched them by accident. To address this issue, I modified the rounded ends of the clip that fits into the 2020 extrusions and gave them...

I installed a Duet wifi and didn't get a screen and after using it I realized I haven't run into a time where I felt I needed it. I have mounted the control box on the back pointing upwards, the hole in the center is for the wires going to the...

This is a custom cable holder designed specifically for E-axis cables. Its sleek and compact design makes it an ideal accessory for any 3D printer setup. Inspired by the innovative design found at Thingiverse, this holder provides a secure and...

This is a remix, taken from two of Hangtight's designs, the one linked and this one https://www.thingiverse.com/thing:3241793 and modified to fit this bracket for top mounted linear rails: ...

I made some changes to the design, but I couldn't make it fit around my machine's bearing sleeve, so I came up with an alternative based on the DIYPark original. To fix the issue, I lengthened the main arm and increased the ID of the bearing sleeve.

I got the idea by improving the design of the maker "TwinA"(https://www.thingiverse.com/thing:4011057). I tried to achieve this by reducing the supports and strengthening the fixings. It also showed that the play between the PTFE tube and the...

Mounting is the Same as my other h2 mount https://www.thingiverse.com/thing:4889163 Nozzle to Probe -33,-11, Z should be same as stock mounts using 2 M3 x 8mm botls for the H2 and 2 M3x 8mm bolts (may want use a washer) and 2 m3 nuts for the Bl...

A basic table to hold the Sunlu Filament Drier under your print bed and off to the side so you can dry while you print!

Optimised flow for more cool air for the extruder

I designed this to ensure that there is no pulling and twisting forces on the bowden tube, this ultimately ensures that there is less wear and tear on the bowden tube over time. I got this idea because I saw the bowden tube twisting during...

Basic screw on X-axis motor strain relief. ... Print horizontal and you'll need M3 screw + nut.

My printer is enclosed by affixing plexiglass to the frame and has a removable cover over the top. I wanted to heat up the chamber so I came up with this solution. I bought the heater from amazon. it is a generic heater and does not have a...

Lower holder for the heatbed guide rods, so there is more space for a larger hotend and / or fan duct. ... The original screws can be used, 4ea M4 nuts are also required.