ender 5 plus upgrade 3d models

I made a 90 degree bracket for the 2020 extrusion for the Ender 5 Plus

The Creality Ender 5 Plus comes with a single gear extruder as standard issue, but users can opt to upgrade to a dual gear model for enhanced functionality and precision control over their filament feed. ...To prevent unnecessary wear on the PTFE tube...

CREALITY ENDER 5 PLUS SPOOL HOLDER CENTERED BRACKET EASY TO PRINT As my Ender 5 Plus arrived, I found the spool holder fixing needed improvement. You may also notice that I've used my "Creality Ender 3 5 Pro Plus Universal Ball Bearing Super Easy...

Ender 5 Plus run out sensor bracket for dual drive extruder (BMG type).Bracket places run out sensor at correct offset for use with dual drive extruder like the BMG.Adds filament guide.Link to Ender 5 Plus firmware config and cable management photos....

This is the X Endstop Version for the Ender 5 Plus with the Micro Swiss Direct Extruder Plate mounted on Linear Rail's.

Because the metal dual gear extruder for creality Ender 5 Plus has a different entry path for the filament then the plastic extruder, a spacer is needed.

Ender 5 Plus Stock X Carriage Plate - Hero Me 7.2 Bolts directly to it This file was created by the Great Work of: bametalman

This is a remix of Hero Plus ver6 OEM and MicroSwiss with BLTouch created by mediaman adapted to Creality Ender 5 stock hot-end plate. ... Base STL: Hero_Plus_OEM-Micro_Swiss_Adj._BLTouch_ver6.stl can be found here.

https://www.thingiverse.com/thing:4790166 I've upgraded my ender 5 plus to use a BTT SKR2, BTT TFT 5.0 v3, Mean Well Se450_24 PSU, and a TH3D Mosfet, so all kinds of holes had to be moved. I redesigned the PSU case based on the concepts of Marty_Z's...

This is a bracket for the Ender 5 Plus to hold the Meanwell 600W SE-600-24 in the Ender 5 plus's stock housing. This can be done with slight lengthening to some power wires. ...There are two stl's attatched, one designed to be drilled for 4mm inserts...

Chain mounts and bl touch mount for ender 5 plus + microswiss direct drive After adding the Hero Me Gen5 to my ender 5 plus I didn't have a bracket that fit my bl touch and I wanted cable chains so I made mounts for them.

This will be fixed in an future version.Edit (3.5.2024 Hotfix!) :Due to some weird measurements, the adapter didn't fit, because of the screws of the mounting plate of the Ender 5 Plus.Edit (2.5.2024) :Unfortunately, I had a very busy time last...

This is my custom Palette 2 teflon tube clip designed for my Ender 5 Plus, which boasts an upgraded all-aluminum MK8 extruder sourced from Aliexpress (link below), featuring a higher profile than the standard plastic extruder that comes with the...

At https://www.thingiverse.com/thing:4821969 jerryfudd designed a Ender 5 Plus Power Supply Casing Noctua 92x14mm RSP-500-24. ...I made this remix so that the openings fits for the new Noctua fan.

remix of hangtights fantastic design. ...remixed the base so it fits the ender 5 plus. ...without this base the bl touch is not able to be mounted and the base plate wont fit the carriage.

https://www.thingiverse.com/thing:4141056 and https://www.thingiverse.com/thing:4738723 I needed to have something that would fit the "Ender 5 Plus" that: 1) Would hold the bowden tube 2) Account for the extra spacing needed for the BLTouch Bracket...

I found the standard cooling shroud on my Ender 5 Pro and Ender 5 Plus to be a little inadequate. I couldn't find a model on Thingiverse that seemed to match my printers, both of which have Microswiss direct drive extruders. ... This is a simple...

I wanted to put a Raspberry Pi 4B on my actual Ender 5 Plus. I designed this one specifically to fit the Smraza case that I have...

I want to put a Raspberry Pi 4B on my actual Ender 5 Plus. I designed this one specifically to fit the Smraza case that I have...

... sensor holder to the Micro Swiss Direct Drive mounted on linear rail carriage. ... You will need to follow instructions on [Ender 5 Plus Linear Rail Conversion](https://www.thingiverse.com/thing:4578889) so that your limit switches are setup correctly

object holder upgrade ender 3

Minimal support is needed.Ender 5 Plus - Print on the side opposite the PCBA connector opening. These models are tailored to Ender 5/Pro/Plus which have been converted to the ZeroG Mercury One CoreXY system.Ender 5/Pro version mounts to the rear...

... housing that comes with the Ender 5-Plus. This can probably work on other creality machines that use the same filament sensor housing/microswitch as the Ender 5-Plus You might need to hot glue the PTFE tube to the housing so it doesn't move around

... correctly, this design incorporates a filament guide. For those interested in implementing this design on their Ender 5 Plus, you can find firmware configuration and cable management setup guides here: https://www.thingiverse.com/thing:4544301

The support for Dahua Consumer Camera I've designet for my Ender 5 Plus. 20cm high simple to redesign in TinkerCAD. Also in the package there is holder very similiar to original holder if you lost yours. ... Added more rigid v2

Cable strain relief for Stockman59's Hero Me Gen5 mod for the ender 5 plus with Microswiss DD. Use M3 x 8 or 10mm, not sure which ones fit. Has 2 slots for small cable ties to thread through. ...Print on its back (so the curved surface where the cables...

update 12-01-2020: final version Component cooler for the Ender 5 plus with Mosqito Hotend and 5010 fan. ... matches the other Mosquito components I designed: Mosquito Adapter: https://www.thingiverse.com/thing:4662770 New Version Mosquito...

This adapter simplifies installation of the Mean Well RSP-500-24 power supply unit into your Ender 5 Plus significantly. You will need (8) M4 x 8mm button head screws and (4) M4 nuts to complete the process.\r\n\r\nInstallation note: Extending some...

Made this to mount 7" Pi screen to my Ender 5 Plus.Should work in any extrusion with adequate space.Made for use with Pi Screen Case https://www.printables.com/model/237957-raspberry-pi-7-touch-screen-display-lcd-tft-case-e4x M3 bolts4x M4 bolts4x M4...

This is a Remix of a Cable Support for the Ender 5 Plus. But i didnt find that Thing again on Thingi. I just made the space between the holder bigger so it fits with the original BL-Touch Plate. ... You have to ad support to the holder but not to the...