ender 5 pro power supply 3d models
764571 3d models found related to ender 5 pro power supply.thingiverse
... and involved. Designed these to drill and thru bolt into the power supply housing and rest on the 20/20. Orientation with the holes down to eliminate the need for supports. Creality Ender 5 Pro .15 resolution 25% infill Brim No rafts No supports
thingiverse
... can hold the PSU perfectly. NOTE: in case you don't know where the PSU screws are, they are under the Ender 5 (Pro) sticker on top of the housing. ...Just make a hole for each one or remove the whole sticky mat: https://imgur.com/h5JcAry
thingiverse
4 simple prints to mount the power supply on the back of an [Ender 5](https://www.amazon.nl/dp/B089CFWYL1/ref=cm_sw_r_as_gl_api_glt_i_Y8421XE8TJ5TDDZ6YYJR?linkCode=ml1&tag=3dprintlinks-21) 2 more mounts for the top are coming soon
thingiverse
support for positioning the ender 3 pro power supply on the table
thingiverse
Ender 3 Max/Pro Power Supply Cover that holds the USB and the hex keys
thingiverse
Very simple remix of the Ender 3 Power Supply Fan Silencer by [Heikomarx] so that it fits the Ender 3 Pro Meanwell power supply.
thingiverse
Tool holder for Ender 3 Pro power supply. ...Works as is or stick down with 2x tape.
thingiverse
Power Supply Support Ender 3/Pro to install a doble axis Z Printed with: 0.6 nozzle 0.32 layer height Need Supports
thingiverse
Ender 3 Pro Super Silent Power Supply with 92mm Fan https://www.amazon.de/gp/product/B01L6PMFAU/ref=ppx_yo_dt_b_asin_title_o03_s01?ie=UTF8&psc=1
thingiverse
This is power supply modification for ender 3 pro. ... You need to remove the original cover and replace it by new cover with 80x25 12v fan The frame and the cover mounted by screws from fan.
thingiverse
Just another fan silencer for the ender 3 pro. ... Note! Never have both screws removed at the same time or the fan will drop into the power supply case.
thingiverse
This is for Ender 3 Pro power supply only. Needed Aux power for Raspberry Pi mounted in rear custom case. http://www.thingiverse.com/thing:3688967 Ender 3 all in one, universal rear electronics case by TeachingTech is licensed under the Creative...
thingiverse
After printing the power supply holder from kevinakasam's Belt Driven Ender 3 mod, I noticed the gap at the top between the PSU. The Ender 3 Pro has a different PSU than the stock Ender 3, that is not only thinner, but the mount holes are...
thingiverse
https://github.com/boubounokefalos/Ender_SW/tree/main/STL/Electronics Since I replaced the stock leg extrusions of my Ender 3 Pro with 500mm 4040 extrusions in order to better match the stock Voron Switchwire, I needed a better way to mount the...
prusaprinters
This is a holder for the MeanWell LRS 350 power supply that mounts to a 4040 extrusion.After printing the power supply holder from kevinakasam's Belt Driven Ender 3 mod, I noticed the gap at the top between the PSU.The Ender 3 Pro has a different PSU...
thingiverse
I needed mounts for my power supply on my Ender 3 Pro. Easily found a file for the board and screen but couldnt find anything I liked that would allow me to lay it horizontally and space it up for air flow. Shout outs to MrClown for the electronics...
thingiverse
4 X M4x8mm for mounting to the v-slot on the side of the leg 4 X V-Slot nuts As the power supply is not grounded to the frame now, you should run a ground to the frame. There is a cut out for it on the back of the leg to run ground to. ... You will...
thingiverse
When I upgraded my Ender 3 Pro to dual Z axis, I needed to move the power supply. I did not want to mess with taking it apart or turning it upside down, so I created these options and ultimately chose to mount it in its original location, but...
thingiverse
... hammers, ...). Files for Ender 3 PRO (LRS-350-24V): -big cover -small cover -mounting angle for M3 screws -T-nut for M3 nut (snug fit) Parts needed for mounting: -M3 nuts, M3 screws Print settings: -Print with brim -Prints fine without support
thingiverse
Since I was going to install a second Z axis kit in the rare 3 pro, I had to change the location of the power supply. However, since the Z axis development parts haven't reached me yet, I prefer the power supply to be shiftable on the profile. This...
thingiverse
Having recently purchasing a Creality Ender 3 Pro, I loved everything about it apart from the bare power supply bolted to the side if it. I decided to make this in order to clean the visuals up a little. Use double sided tape or foam pads to...
thingiverse
Very simple remix of the [Ender 3 Power Supply Fan Silencer](https://www.thingiverse.com/thing:3328495) by [Eigengrow] (https://www.thingiverse.com/Eigengrow/about) so that it fits the Ender 3 Pro Meanwell power supply. I printed off a few layers...
prusaprinters
Remix of "V Slot Rail - 20 mm x 20 mm" by somaraok (thingiverse.com/thing:741325) and "Power Supply Fan Silencer" by rovanni (thingiverse.com/thing:4251317).This cover can be mounted without unscrewing the power supply fan. The fan cover was remixed...
prusaprinters
This mount offsets the power supply a little to the side so you can use dual z lead screw mod (single stepper, belt driven) on your printer You will need: 2 x M4x16 screw 2 x M5x16 screw and M5 nut Print Settings Printer Brand: Creality Printer: ...
thingiverse
Power supply cover to replace the fan with a quieter one. ... Fan 80x80.
thingiverse
Just a simple decorative cover for the Ender 3 Pro PSU. ... Original model at thangs.com: https://social.thangs.com/m/822959