ender 5 s1 firmware 3d models

Made this for resonance measurement. ... https://www.klipper3d.org/Measuring_Resonances.html

First remix, I used TinkerCAD to modify the USB holder and replaced it with a slot to hold calipers which wiped out the original two slots in that location. ...And of course I added my branding.

This is not a remix. It may look like others on this platform but it is a complete redesign from the ground up. Advantages over others:- 1. It is extremely accurate and will fit your sprite extruder perfectly if you have your printer set up...

After installing the factory light bar I could not use the tool holder that I downloaded from here, so I decided to create my design my own. ...This is my first time uploading on this site

This is a holder for the Ikea Led stripe. It holds two of them. ...Easy to print and install.

This 3D printer enclosure is designed to control the flow of heat and fumes within the print environment while printing materials such as ABS and ASA. The frame is constructed using 2020-profile aluminum extrusion, and the walls are made from 1/8"...

Yes you can now include the stock plier from Creality. I know it's not perfectly designed so I had the STP uploaded. ...You can now edit it to fit your own tools.

Customized version of https://www.thingiverse.com/thing:34558 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=34558

Remixed from:https://www.thingiverse.com/thing:5511795

if u dont like sensor...this one better for your style...

This Scraper Holder might look like it won't fit, but you must put some strength into to put it on. ...If it breaks but stays on its fine.

10% - 20% Infill Supports needet

Customized version of https://www.thingiverse.com/thing:3141591Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3141591

This design snaps onto the top crossbar of the printer. A PTFE tube coupling with a diameter of 9 mm is screwed into the top. At the bottom, the filament can be pulled through a funnel shape in any direction. ... The sensor can be screwed on directly...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/gMOhoKYwasT

this is a remix from https://www.thingiverse.com/thing:5276532 wanted something that mounts a bit firmer to the top bar but did not want to remove the screws. ... attached the tinker cad files in case someone wants to edit further

Did not want to hassle with printing a Bolt, Nut and Stopper that was going to take 11 hours to print and have to deal with multiple pieces every time I wanted to swap a roll. There is always a better mousetrap. This prints in under an hour and...

I designed this roll holder to use rolls that have a smaller center or were longer than the original roll holder that comes with the machine. ...There are 2 versions, both are the same file but the first one is cut in halves to print without holders.

hi this is a simple remix only adding a "hook" for anything really

Little gear wheel for your extruder

Holds all the tools that came with the 3S1 plus a couple of your own. Has slots for SD cards. Fits nicely in the left side of the filament spool holder and locks in place so it won’t vibrate off. Printed with PLA at the basic settings for the 3S1...

Side handle rated for 20 kg/handle with ABS filament (S.F 2.1) It requires one T Nut/handle (Supplied with the printer) Spool and filament runout sensor can still be at the center.

This bracket has been designed to replace the stock bracket that comes with the Ender 3 S1, it comprises of three prints. The main bracket that screws in to the same holes as the stock bracket with the stock screws. There is also the lid which is for...

It is a remix of the hero me gen 7 single 5015 fan duct to make it fit for a Creality Ender S1 & S1 Pro. Most other Ender 3 S1 & Pro ducts are routing them to the right side of the CR touch module; however that results in a narrow air channel...

Small little tool holder that clips into the V-Channel of an Ender 3 / Ender 5 model printer. ...Holds a ruler, plyers and tweezers.

4) plug a USB cable from the PC to the mainboard's USB port and connect the application to the printer 5) follow the instructions provided by your application to flash Marlin firmware 6) Once Marlin firmware is flashed, disconnect the application...

have fun ;) --- Da es keinen Halter für einen Laser gab den man direkt auf die Ender 3 / Ender 5 Hotend Platte schrauben kann, habe ich nun einen erstellt. Den Halter einfach auf den Laser schrauben, Hotend und Lüfter demontieren und den Laser...

Direct Extruder Mount for Ender 5/5+

Netatmo Smart Smoke Alarm spool holder for Creality Ender 3 S1.