ender 5 s1 firmware 3d models

A convenient way to attach a pi-top [4] to an Ender 3 v2/S1 display mount, using screw-in studs to slot in. ... Print 2 studs from here: https://www.thingiverse.com/thing:5195246

The bracket to mount the stock fan an the right side can be found here:https://www.printables.com/model/213509-right-side-bracket-for-ender-3-s1-stock-fan

This is a Mount for MKS Mosfets for the Creality Ender 5 (Pro).

bowden anti-hitch derailleur for ender 5 pro, fits over the X motor.

Belt tensioner & linear ENDER 5 Belt tensioner link: https://www.thingiverse.com/thing:4127601

I maked a Filament Runout Sensor case for my Ender 5 3D printer.

Um den Ender 5 Stabiler zu machen, Layer schöner zu drucken. ...https://youtu.be/uegQAe5K8NU

Clips onto the Ender 5 and is designed to hold an elmers glue stick (22g).

Direct Drive Ender 5 MGN Linear Guide Upgrade Kit - Elevate Your 3D Printing Experience

brackets to support the electronics on the side of ender 5 plus

You can attach your octopuses directly to the Ender 5 frame with this setup.

Remix of the Ender 5 Phone Mount for an ipad mini

TFT35-E3 V3.0 mount for Ender 5 Plus. ...You don't need any screws.

Ersatzteil für meinen Ender 5 Plus, da der Eckwinkel / Eckverbinder gebrochen war. ... Winkellänge 35mm

PiCam holder, which fits in the cornerbrackets on the Ender 5. ...No screws needed

Vertical Support Clip for Ender 5 Plus, a Convenient and Reliable Solution for Smooth Print Jobs

Ender 5 Homing Switch Enclosure for X, Y, and Z Axes.

This is a custom bracket that holds the ender 3 s1 display with an integrated raspberry pi 3(b) case. This has a 3 screw mount that uses the stock 3 screws and replaces the stock display mount bracket on the ender 3 s1. Use 4 m2x10 or m2x14 screws...

Side Spool (left or right) filament guide with filament sensor for Ender-3 S1No support needed -Gcode included is for Ender-3 S1 PLA / 0.2 / 15% infillIt made for PC4-M10 PTFE connector(This is a remix from fluxxie's design...

A simple toothed belt clamp is needed to repair or replace the toothed belt on the Ender 3/5. ...Two M3x6mm screws are required for each clamp.

Printed on Ender 5 proresolution 0.2mminfill 100%wall 1.2mm

If you want to use Spool Holder Inside the Case with Ender 5 Plus you need to shorten the Spool Holder. ...Original one is hitting the bed!!

Used 2 linear rails 350 mm MGN12 from Amazon. M5 bolts 8-10 mm (12 of them) or reuse the ones holding rollers with nuts. As the rollers are removed, it made a space for side light in side right V-rail (connected to an existing switch for the top...

I made this to lower my spool holder becuase it wouldn't fit on my shelf but i didnt want to make a whole nnew spool holder either. ... This goes right on you original spool holder like the normal stick does and then you just attach the spool stick to...

Prints well without support. Clears frame when homing without a problem. ... I recommend using cable tie to hold the cable in place as I did on the photo.

Support to hold lower cable close to the machine for better support and routing

The bracket provides an alternative way to fixate the filament sensor to the gantry. ...This can be useful, for example, in case the dedicated original spool holder fails, or is removed from the machine.

Do you like my work? Can you support me with a ☕ or maybe a 🍺? It all depends on the moment 😄 Double-sided guides to stick to the underside of your tray to place your PEI plate correctly and quickly. Suitable for a wide range of printers. ... I...

Cable guide for print head. Slides over existing guide and helps to turn the cable 90 degrees to eliminate bending the cable off - axis. ... Flat spot for zip tie to hold cable flat against guide after 90 degree rotation

This is the "shake-hands.stl" file that comes on the included SD card along with the rabbit, car etc. Uploading it here as some customers reported their SD card doesn't have it included. ...There are two holes underneath the bed that it attaches to,...