ender s1 plus upgrades 3d models

(In Progress) had to make some slight mods to fit the printer. And I might have to do more mods until it is just right. But here's a few photos of the progress. Any tips or advice would be appreciate. I've added the stls I'm currently using. But I...

I needed a bracket to keep my cable from ending up like so many others I've heard. ...I took measurements from my own printer and created this in tinkercad.

Remixed DarkedgeUK's remix.https://www.thingiverse.com/thing:5455161/remixes.Used the DarkedgeUK version for a while but got tired of it getting knocked around (by me mainly) so I decided to make a fixed version. ...Flipped the bracket and attached the...

The mount may fit on top of other printers with the same type of extrusion but has not been tested. ...I used m5 bolts with t-nuts to attach it.

Just a little version to avoid any extra hardware.

Because of the narrow place where my 3D Printer is standing I accidently touched the Powerswitch of the Printer ..... ... I was able to continue the print but this should now never happen again :)

Added a arm with a small screw with 1/4-20 UNC threads and a cable pass-through on the arm. Add a bit of teflon tape to the screw to make the webcam sit a bit more snug. ...

Adapterplatte zur optionalen Montage des Lasers an den Montagepunkten des Sprite-Druckkopf. ... Adapter to mount the laser at the same points as the printhead.

Use 3.5mm mica for laser cutting or direct printing. ...Some of the required components include: - 1 12v fan size 50x50x20mm - 4 M4 screws 25mm

Useful for using Klipper or Octoprint, as the screen can become unused. Works with most Raspberry Pi's, it fits my 3B and 2B anyway. Should fit the 4 too. All of the ports are still useable, and the SD card can still be taken out. ... The Pi slides...

Cooling from 3 sides. Is splited in 3 parts for better print qualty. The cable for the nozzle fan is stretched to max. First looks like it's not long enough but falls into place while assembly. ... Hardware 2x M3x20 & 2x M3 Nuts needed The...

Remix for the Gantry Tool Holder by RonBen (https://www.thingiverse.com/thing:6122185) Modified to store spatule with a gap for the plastic part, replaced some gaps with holder for microSD card reader with type-C adapter. ... Also branded with my...

JUST FOR FUN

Should snuggly fit onto the front of your printhead to indicate the Norse Gods bless your project (and that the filament hasn't jammed!)

optional cooling fan for the mcu, mark your holes for fan choice, i used heated nutserts.its a tight fit.

My printer is in a tight spot and I needed something to hold just the filament sensor. Since the filament spool is inside the cabinet, the part that I remixed this from didn't work well because the filament would need to bend too far and it would...

I used the camera body from codemonkey 1973 and made my own rail mount and arms The mount sits on the x/y rail

I have put the top ring separately to avoid the need for support. You can glue it after. ...The length of this print is shorter than the original holder.

Created this to slip over the cover for the X axis stepper. Tried to replicate the angular design of the cover and bring that into the mount itself using draft angles, but I provided a second version with a traditional filleted mount. The internal...

Got worried on how hot the stepper motors were running using a Sonic pad- so hot you couldn't touch them. Uses a single 2280 NVME cooler cut in two (30/40mm) and stuck to the rear and LHS of the motor. Designed this to simply clip over the motor...

2023.3.6　UP DATE 　Added tall Ver. 2023.3.6　UP DATE 　Added Rod riser clip 10mmRise ＆ 15mmRise Replace mounting bolts with M3x8mm bolts. Use M3x10mm bolts for knobs. The thickness of the mounting portion of the dial gauge is 8mm. Use...

When you're making a Bed Mesh, remove it or it will interfere by really tightening the ribbon

I've had problems with bed leveling (wrong layer height acros entire bed - cr touch working properly, Z axis screws was moving, but it had wrong measurements because there is some problem in Y axis) like many others as i can saw through internet. Now...

Created as a replacement for the original. Designed for 40x40 fan. It is necessary to purchase this for easier assembly ...

Hello I made this fan duct for sprite extruder. It is still in testing but for now everything works fine. I`m pretty new to Fusion 360 and i made it for learning purposes. You need: 2x 20mm M3 screws 1x 12mm M3 screw *EDIT* Added new...

I wanted a camera holder for my new 3d printer and I liked the cam mount made by ChrWieg but didn't like it required a screw through the base. So I found the tripod holder by PiAir and I decided to mix the 2 together. ...Hope you enjoy.

A little clip that holds the extruder ribbon cable in place. Designed to reduce stress on the X motor wires. ...No screws or tools needed.

I liked Aiirik's design but couldn't use it for my Creative Live Cam. I imported it into TinkerCad, removed the Wyze mount, added a slotted hole for adjustability and cut off the from corners to clear the camera mounts overhangs. ...The 1/4-20 slot is...

I added a Wyze Cam V2 mount point instead of the screw hole in the previous design. This also allows you to tweak the angle of the camera to your liking on the mount since the Wyze Cam can move on its base. The Wyze mount point is not the full...