ender s1 plus upgrades 3d models

Wanted to put my BigTreeTech SKR 2 board in the middle of the open space to have access to all sides of the inputs, including the USB port for a Raspberry Pi running Klipper, but Kersey Fabrication's mount pressed the inputs up against the case, so...

I changed this up to have a bit more on the end of the arm. I hate when a design is cut off. It looks weird. I also made the mounting holes for M4 flat heat screws, as that was what I had on hand. ...I T-nuts are also from the filament sensor that...

dimensions are 14 by 14 by 4.1, might need to try 4.15 or 4.2, 4.1 was enough to fix my issue which was a clicking noise inside dimension is close to 12

I enlarged the mounting holes to accommodate an M5 cap head screw.

I required a variant that could be installed without having to reverse the extrusion, in order to insert the original tool (https://www.thingiverse.com/thing:4198943). So I designed this version which utilizes 2 x M4x8 bolts and 2 x M4 T-Nuts. I have...

HOW I MAKE IT: <iframe width="560" height="315" src="https://www.youtube.com/embed/RpIH-jXLHm8" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> MATERIAL: ...

Hardware needed: -M8 tap -M8 bolt -608 bearing

This is a motor mount designed to mimic the stock motor mount with the lower section where the filament runout sensor would be removed. I used this mount while working with the 3DChameleon MK2 as I needed a way to mount two motors side by side...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

This Thing uses the Blokhead of dpetsel https://www.thingiverse.com/thing:2759439 I needed a light source to see what the Printer is printing.... So there is a holder for a COB/LED Light strip of 5-7cm to enlight the nozzle. ... Enjoy it ;-)

Touch Sensor Protection System: Preventing Catastrophic Failure We designed this system specifically to safeguard the BL touch sensor. Its primary function is to protect against X-axis runaway, a potential cause of sensor damage. By implementing...

To connect 2 PFTE to sensor. ... Update - now right scale.

Shortened version of https://www.thingiverse.com/thing:3020026 (can't get it to link!) Made so it can still sit on the inside of the frame as I have a wall behind. ... Adjusted to print on side with minimal support.

Made a split version SO I didnt have to disengage the motor etc. Debranded . ...

This is spacer for filament sensor to use with dual gear extruder. ...This spacer will align sensor exit with extruder inlet.

Blocks are placed along the x-axis rail to ensure it aligns perfectly with the frame. First, loosen the screws holding the wheel carriages in place. Then, adjust each eccentric wheel nut independently on both sides of the carriage until they're...

This remix adds a fitting for the filament input path that can be used either for a dry-box or as a guide to keep the brass bushing on the sensor from shredding the filament as it feeds. This version also changes the sensor mounting holes to use...

This is a modified Version of the aftab's cable chain tray: https://www.thingiverse.com/thing:4164988 enjoy it :-)

This is not a remix of but was directly influenced by this Thing: https://www.thingiverse.com/thing:3836394. The retractable badge holder is an ingenious concept that I wouldn't have come up with on my own. It keeps your cables from sagging and...

I've adapted the style of belt tensioners on my Y-axis by shortening the inner arms, allowing them to press firmly against the front horizontal extrusion. Having successfully implemented this modification, I was pleased with the outcome. However,...

Lower holder for the heatbed guide rods, so there is more space for a larger hotend and / or fan duct. ... The original screws can be used, 4ea M4 nuts are also required.

This is a remake of https://www.thingiverse.com/thing:4091776 The mounting bracket did not fit my needs, so i used the cooling fangs from the original thing, and made a new mounting bracket, fitting my Kay CoreXY convertion. Printed with tree...

I installed a Duet wifi and didn't get a screen and after using it I realized I haven't run into a time where I felt I needed it. I have mounted the control box on the back pointing upwards, the hole in the center is for the wires going to the...

# I'll be updating this shortly with the parts list and more details # ### Why? ### This started because I wanted to use the Bondtech extruder as direct drive with a v6 as it was intended. This was before the release or talk about the Micro Swiss...

A human requires an additional module to be installed.

The carriage wheel spacers now fit through the part for a more secure location. A support tube now keeps the Bowden tube from flopping over to one side. I didn't like how the corrugated tube was bundling cables with the Bowden tube, so I removed...

This is included in the Files. All parts print in the given orientation with NO supports or brims. I recommend you print the parts in PetG. I used M5x12mm bolts to replace the grub screws in the 60t pulleys for better grip. Lightly sand...

Mounting plate adapter to use microswiss direct drive plate with the exoslide system To mount remove exoslide, mount plate to exoslide then mount plate to microswiss plate then mount exoslide back on rail

Relocates the Y axis stop sensor to the back rail to allow for horizontal movement for exoslide plates