ender v2 vs s1 3d models
175262 3d models found related to ender v2 vs s1.
thingiverse
Fix for a broken extruderarm on the Ender V2. Did a completely new part, since the measurements for the Ender3 replacements seem to be different. Added extra material in the high stress areas to counter any crack formation. This requires the...
thingiverse
This is a DIY enclosure for the Creality Ender 3 V2. Printed parts list: (OPTIONAL) 1x hacksaw_block 16 x 4_mm_plexiglass_fixing 8 x 20x20_three_way_corner All other printed parts that is included in the download but not listed above is so...
thingiverse
Needed some feet for my Ender 3-V2 after upgrading the PSU fan and printed this cover for it : https://www.thingiverse.com/thing:4567153 These feet are simple and clean and fits over the rubber feet that are on the printer. There are two versions...
thingiverse
The Aim of this project was to build a converter kit for my V2 model into a Core YX printer and by reusing as many original parts of Ender 3 v2 as possible. The second goal of this build was to keep the possibility of converting back the coreYX to...
thingiverse
This is AirMachine a Ender 3 V2 fan duct for x2 5015. The Idea behind this duct isn't only to provide lot of cooling but to make working at nozzle easier, you can remove the face and have free access to heatsink, etc. Another point is that once...
cults3d
This is AirMachine a Ender 3 V2 fan duct for x2 5015. The Idea behind this duct isn't only to provide lot of cooling but to make working at nozzle easier, you can remove the face and have free access to heatsink, etc. Another point is that once you...
thingiverse
Tete Ender 3V2 pour utilisé deux noctua PWM 40X40, s adapte avec le souffleur d origine
thingiverse
Füße für den / Feet for Ender 3v2 und alle anderen / and other 4040 V-Slot Profile
thingiverse
feet for ender 3 35x20 Spool holder: https://www.thingiverse.com/thing:4721912
thingiverse
This is a redesign from https://www.thingiverse.com/thing:4603075 I've uploades two versions: one with Ender logo and one blank Printed with PETG without Support.
prusaprinters
27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...
prusaprinters
27/09/2020 Designed to fit the Rasp Pi 4 and display for Ender 3 V2 It will fit the lower versions of pi also. Print Settings Bottom: just print flat and will print fine Top: print upright with supports from build plate Cap: print flat 100% infill...
thingiverse
27/09/2020 # Designed to fit the Rasp Pi 4 and display for Ender 3 V2 I believe it will fit the other versions of pi also. # Print Settings - Bottom: build plate supports no raft just print flat and will print fine - Top: print upright at a...
thingiverse
REMIXED FROM PREVIOUS DESIGNS BY FONSWERKS & MDAVYDIV: 35mm total height, will raise printer by 25mm when installed with rubber feet on Ender 3 models. Suggest printing on flat face. .20mm layer height should be max, designed for .4mm nozzle, no...
prusaprinters
It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...
prusaprinters
It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...
thingiverse
Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles. Top main layout for direct drive (Creality Sprite extruder). Top filament sensor all push fit with gap at back for...
thingiverse
Added bigger fans underneath my Ender 3v2, so it needed to be lifted. Why did I choose this design? Because I happened to have some chunks of 90x53x300 foam that I was already stacking the printer on. They provided good vibration dampening, but were...
prusaprinters
🎉 Greetings!I'm thrilled to introduce enhanced anti-vibration feet for the Ender 3 V3 SE/KE/S1. Building upon the success of the previous model, these new feet boast increased rigidity and incorporate reinforcing elements made from TPU for even...
thingiverse
This is an improved version of the exhaust fan shroud for a Loque Raw S1, it helps direct air out of the case rather than blowing it against the panel and much of the air remaining inside the case.
thingiverse
This is a Sonic Pad mount remix from the one made by xTNR https://www.thingiverse.com/thing:5555205 Used in my recent review video for the Ender-5 S1 + Sonic pad https://youtu.be/KpixXeWQiaQ
prusaprinters
Those are Two little spacers to fit the original Creality Light for Bigger printers on the Ender 3 S1 PLUS. Just Print one of each and you are good to go to screw the light on your printer. ...The light need to be conected dirctly to the 24V Power...
prusaprinters
Designed to set on top of the display on either the ender 3 v2 or ender 3 s1 (which has the same screen). ...Helps keep the screen dust free and is very helpful for blocking the light at night.Print Instructions: Print flat with supports for the over...