ender v2 3d models

Ender v2 CoasterDesigned in FreeCAD.The .stl is large so scale it down to 75%  and set z height to 4mm in the slicer.Ender 3 v2, Generic Silk PLA, 0.4mm nozzle, 0.2mm Layer height.

remix of https://www.thingiverse.com/thing:3294512 and https://www.thingiverse.com/thing:1415895 to fit the Ender 3 v2 with a raspberry pi 3 B+ and camera for octoPi

Cover for the Ender 3 V2 QR code axis motor.

A laser mount for front hot end for ender v2. I printed in PLA .It has many supports and prints in 2:45 hrs. Support removal is time consuming but after removing supports it fits like a charm. It is a must have for people who have installed BL Touch...

Ender Extender V2 Marquee

Suporte Ender 3 - V2

Clips which fit into the hole where the voltage selector switch is located on the back of the Ender v2, for use instead of a stick-on clip to hold the cable after moving the power switch to the front. Two sizes: One fits a flat 2 core cable of...

Ich habe das Level Rad für den Ender 3 V2 angepasst, da der Ender V2 nur M3 Gewindestangen hat nicht wie der Ender 3 und Ender 3 Pro. Das Original für den Ender 3 PRo habe ich hier her. https://www.thingiverse.com/thing:3676273 Ich habe die Datei...

I modified the Ender 3 V2 Direct Drive by JamieBK to fit for an aluminium extruder bought from AliExpress (search for "Ender 3 Extruder" and look for the red ones with orange springs). I used the same print settings as with the original one. ... --...

Remix to suit Ender 3 v2 - Original design by NG_Design Different link brackets for the small chain as the V2 have the power supply mounted under the bed. ... Use same settings as original design and replace Kette_klein_unten.stl by this one No...

this bracket is to fit the ender 3 v2 neo, and it makes a support to put your own metal bracket to hold the motor and extruder. a simple L bracket with a 10 mm hole for the gear to pass through into the extruder. in my case a BMG direct drive dual...

KP08 upgrade for ender 3 v2

Ender 3 v2 için z rot

do not have Ender 3 V2 but it is fine

This is the Cad Model that a made from the ender 3 v2 display motherboard

A Remix Ender 3 v2 Chain. ...After installing test the thermostat and if hits up

Foot for Ender 3 v2. ...Easy to install and fast to print.

A Remix Ender 3 v2 Chain. ...After installing test the thermostat and if hits up

personaliza tu botos de apagado, para que sea mas accesible. ...ender 3 v2

This is a minimalist drawer designed for the Ender-3 v2.

This is the Cad Model that a made from the ender 3 v2 display motherboard

*Still working on adding everything and putting together* IKEA Lack Ender 3 V2 Double Enclosure. ...

Just my design of a design sign for Ender 3 V2.

Корпус экструдера для Ender 3 V2. На обдуве имеется ячейка для светодиодной ленты шириной 8мм. Extruder housing for Ender 3 V2. ...There is a cell for an 8mm wide LED strip on the blowout.

After upgrading Ender 3 V2 with linear rails, I had to add linear rail stop brackets .... ...something simple ...

This design is based on my Ender 3 V2 but it also looks like the Ender 3 and Ender 3 Pro

A Scraper/Spatula Holder for my Ender 3 V2, it clicks on the rails of the 40x40 alu profile. ...So it will fit on other printers too.

Feet for the ender 3 v2. Gives you about 40mm of ground clearance. ...Note that the rear legs are different beacause of the psu cover

Ein Werkzeughalter für den Ender 3 V2. ...(Passend für https://www.amazon.de/gp/product/B08B3MMLRP/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 ) Kann auch über Fusion angepasst werden .

Toolbox for Ender 3 v2. Suitable for profiles 20x20 and 20x40 (up to 4 mounting points). ... External dimensions:70x40x80mm (WxDxH) Also necessary: - 2:4 hammer nuts (t-slot) M4 - 2:4 screws M4x8