engineer 3d model

The hole for the cable tip should be wide enough for any similar cables, but if not you can pretty easily remix the model by just cutting the hole to be larger or adding material where needed. I suggest printing the dock upside down and including...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

I already had some Koss Porta Pros so I printed it and used that for a couple of weeks (after tweaking the size of some parts for a tighter fit, especially the push pin which is/was modelled too small). However, after a couple of weeks using that,...

... with the not dampened stepper motor. Ein von Martin Majewski (@martinjmajewski) gepostetes Video am 5. Nov 2016 um 4:50 Uhr Update 3: I removed the V1 models as they seemed to have some issues. ... V2 is the most current and best working version.

... mount and two each side for accessory mounts. I used one on the right for strain relief for E3D wires, 2 on left for fan mount. 4 on side fan, only two are used depending on fan model. ...2 on cable chain attachment to attach it to extruder mount.

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Druidic missionary of Renmaeth who heard the tale of the Anshani Empire in Edrador. Wishing to steer them from their industrious ways, Myrion travelled to the far away...

You can find the newer version here: Phone Mount for Van Moof S2/S3 V2.0==================================================================== Rotating Phone Mount for the Van Moof S2/S3 electric bike.Mounts to the handlebar using 3 cable-ties,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

- Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

All overhangs should be 45 degrees or less. Rafts: Not required, unless you experience adhesion issues. License The "Hard Drive Holder" models (.stl) are licensed under the CC BY license by Code and Make. The "Hard Drive Holder" code (.scad) is...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

unless you have a special edition like a Porsche, Mercedes, or older Audi, VW, or BMW model, which is what I have. For most of these special editions, the original push bar won't fit. I found a design on Thingiverse called *Klein-laui* and tested...

I need thosethree measurements from that photo: Front standoff spacing, back standoff spacing, and front-to-back spacing.I've already helped several people from across the globe and I've been updating this document with the new models as I go.Post...

This model is only to demonstrate the principle, not to resemble the original (destroyed) or replica (Deutschen Technikmuseum, Berlin, Germany: https://sdtb.de/museum-of-technology/exhibitions/1256/). This is an improvement of <a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

Use at your own risk!!Check out the current version of this design here. This design is tested and ready for use, but only uses one blower, not two.</strong></p><h3>Basics</h3><p>This design stemmed from my desire to create a perfectly controlled and...

http://www.thingiverse.com/apps/customizer/run?thing_id=406494 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

The build and schematics can be found at: https://www.printables.com/model/282166-runtime-counter-v-20 This box will fit in the enclosures made by Stepcraft. Hardware: DS 15 connector female (signal out) DS 15 connector male (signal in) Mono...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

Research I found two suitable models on Thingiverse which I thought could be easily enough modified: Tweezers for SMD by Ruslan_Kulibin SMD Test clamp by Tom20170 which I both printed yesterday. They are both quite nice designs, I especially like...

On the single phase motor models there's contactors and timers in there for the auto tapping function... if fitted. I wired the 12 volt psu's mains connection to the main switch of the mill, this is after the main fuse so it's protected by that,...

Thus I found my way to thingiverse and sought for every model that was irregular eventually finding some customizable builders. While the brick making one is heavy, beam kind was cool, but limited to either halfheight simple or up to # shape with...

Check out the rest of furniture models from it, as they will fit nicely with this mini set! Bar pieces have special connections that allow you to attach them to each other in an unlimited amount of ways, and create any shape of bar that you desire,...

... 4 mm have been printed. If you're printing at a 0.2 mm layer height, simply add a color change at 4.2 mm (layer 21).If you're looking to make the game conveniently portable, check out Thessiell's lid.&nbsp;Don't forget to rate and share your make!

However another person created this and the subsequent prusaslicer ini file. however I am not quite knowledgeable enough with gcode and prusaslicer to make the necessary adjustments to it to make it work on the mini (plus I prefer to do it directly...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...