eq3 2 3d models
931635 3d models found related to eq3 2.thingiverse
The top polar alignment cover for the EQ3-2 telescope mount. Beveled sides to ensure tight fit. ... When it does not fit fully add tape to the sides.
thingiverse
My little contribution to this nice bracket set : The brackets for synscan motor controler and handset, adapted for EQ3.2 aluminum tripod
cults3d
My little contribution to this nice bracket set : The brackets for synscan motor controler and handset, adapted for EQ3.2 aluminum tripod
thingiverse
Remixed this controller mount for the EQ3-2 controllers battery case too. ...Print Settings Printer: XYZ Da Vinci Mini W Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 20%
thingiverse
The bottom of my eq3-2 tripod broque, so I designed this drop-in replacement. Use an M8-30 bolt inside. ... I also designed a bottom leg extention to avoid the tripod to penetrate slowly the soil during a session
cults3d
Just a simple holder that clips or bolts to one of the tripod legs on a Skywatcher eq3-2 tripod that holds the manual motor controller box. Designed in Tinkercad and then tweaked and twisted in 123D. ... 1 version is without the screw mounting hole and...
thingiverse
In addition to printing the piece you will need: A washer with a hole of 12mm A nut to hold the dovetail to the tube (see picture) _____________________________________________________________________ Cola de milano vixen para poder poner el...
thingiverse
Just a simple holder that clips or bolts to one of the tripod legs on a Skywatcher eq3-2 tripod that holds the manual motor controller box. Designed in Tinkercad and then tweaked and twisted in 123D. 1 version is without the screw mounting hole and...
thingiverse
This is a pier mount I created for use with my EQ3-2 Pro mount. It fits a 95x95 end (see attached picture) which I have mounted on a 95x95 pole that's anchored by a concrete plinth (also depicted as an attached picture). It's easy to mount - fasten...
thingiverse
my 3d printed bracket to hold the synscan unit on a standard Celestron eq3_2 tripod https://youtu.be/Vdawy2VJQGA
thingiverse
I like the original idea, so I did the same for my EQ3-2 mount. ...No more ugly gap between the polarscope and the RA dial :-)
cults3d
I like the original idea, so I did the same for my EQ3-2 mount. ...No more ugly gap between the polarscope and the RA dial :-)
cults3d
A little holder for the 3 hex keys that I got with my Skywatcher eq3-2 mount motors. ...It keeps them together nice and safe instead of them just lying about in the tool bag..
thingiverse
A little holder for the 3 hex keys that I got with my Skywatcher eq3-2 mount motors. It keeps them together nice and safe instead of them just lying about in the tool bag.. ... Print Settings Printer: ctc rep dual sailfished ...
cults3d
Here is a collection of different skywatcher eq3-2 tripod leg controller mounts. ... Hitecastro Focus Controller Skywatcher Motor Controller (thing no:1955868 ) ZWO usbst4 controller Skywatcher Focus Controller ***** Updated with a new mount ***** ...
thingiverse
_______________________________________________________________________ Piezas para las partes de plástico del trípode con patas de aluminio, sky-watcher eq3-2. Al leer varias veces sobre la fragilidad de dichas piezas, su dificultad para...
thingiverse
...... Bracket is for mounting a NEMA 17 stepper motor to an EQ3-2 telescope mount in order to use Onstep controller. I've modified another design to allow for clearance of the RA clutch. An extension to the RA worm gear shaft will be required for this.
thingiverse
In order to clear the Eq3-2 mount doing large movement on RA axis I had to extend the motor mount 30 mm. This requires a 6mm coupler and a shaft of some sort (I used an old 6mm drillbit) The coupler was ordered from Aliexpress. Now I have full...
cults3d
After having a super strong moment a few weeks ago I managed to tighten the locking nut that tight that I could not get it loose on my Skywatcher EQ3-2 counterweight bar. Not wanting to attack it with grips and the likes I decided a simple spanner...
thingiverse
After having a super strong moment a few weeks ago I managed to tighten the locking nut that tight that I could not get it loose on my Skywatcher EQ3-2 counterweight bar. Not wanting to attack it with grips and the likes I decided a simple spanner...
thingiverse
A bracket for holding your Skywatcher Focus Controller which mounts on one of the tripod legs of an EQ3-2 mount. Will also fit the EQ2 and probably several others. Very useful to stop the controller just dangling or using up the accessory tray. The...
thingiverse
This one requires an 8mm M3 nut and bolt jast as the Dec motor but I also decided to move the RJ11/RJ12 connector from the metal support bracket and include it in the cover ( simmilar to the Dec motor) I used hot melt gule to secure the grey...
cults3d
After having a slight accident, well slight might no be the best description, I managed to fall againt the tripod and stupidly tried to catch hold of the tripod to save me hitting the deck and failed and at the same time ripped the grey RJ11/RJ12...
thingiverse
Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627
thingiverse
Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627
thingiverse
After having a slight accident, well slight might no be the best description, I managed to fall againt the tripod and stupidly tried to catch hold of the tripod to save me hitting the deck and failed and at the same time ripped the grey RJ11/RJ12...
thingiverse
***UPDATE*** I`ve just made one wall thicker in DE mount :) Now it fits better :) Use thick shell (I used 5 layers) or increase infill. It seems that even with 30% infill mounts are rigid enough, but there is no reason to save some time - we need...
thingiverse
This is a handbox holder that attaches to the aluminium tripod legs of the Skywatcher EQ3-2 (or NEQ3) mount. ... It has been designed a little wider than the original version to fit the "new",handbox controller with ST4 autoguiding port (red...