esk8 3d models
288 3d models found related to esk8.thingiverse
--- Work in progress ---- I'm currently experimenting to find a good esk8 enclosure to fit the components i'm using. ...If you have any tips, I would gladly appreciate a comment :)
thingiverse
Knob for esk8 remote control. ... Better than original for optimal grip.
thingiverse
This is simple screw down phae wires guide for dual motor esk8's.
thingiverse
This is a simple box for the traditional cheap Esk8 esc (ebay, diyeboard or whatever) there is a washer and gasket file that can be printed out of TPU for better water/dust proofing
thingiverse
This is a grab handle for an esk8, really for any skateboard. ... I would use 3/4 inch wood or sheetrock screws to secure to the deck, typically on the bottom side.
thingiverse
Model of the hellray.de esk8 contoller (vesc) its a great vesc! ...I needed a rough model of it to use for a enclosure assembly, so the model is not 100% accurate but the overall measurements are accurate.
thingiverse
https://hackaday.io/project/161730-open-esk8-remote-v1 I reverse engineered the communication protocol between the board and the remote and implemented my own code based on an Arduino Nano. I build my own PCB around the selected components and...
thingiverse
This box was designed to hold the @solidgeek Firefly eSk8 receiver (Arduino Nano + NRF). <a href="https://solidgeek.dk/docs/firefly-remote/getting-started/">More details found here</a>. The interior of the box is 49mm x 20mm x 15mm. It has a cutout...
thingiverse
Attached to the deck with 14 M4 bolts In addition there's room for: Focbox (single), for single motor BMS Voltage display Charging port Loop key All the necessary wiring Print files vertically (4 files), to make the enclosure additional work is...
thingiverse
ESK8 Controller Mk2 It's been an age since I logged in to Thingyverse... I really should complete some of my unfinished posts some time. Today I present for your collective delectation a Mk2 version of the electric skateboard controller I did a...
thingiverse
ESK8 This is a work in progress! While intended to be a replacement housing for the controller that came with my Meepo longboard the electronics are pretty standard and there's a good chance this design will suit others too. Electric...
thingiverse
... promise ... **Thurbolt is a small start-up with huge dreams!! **We are currently building custom skateboard & esk8 decks, esk8 storage systems, custom electronics.. ...Check them out on www.thurbolt.com , instagram @thurbolt, youtube Kanber M.S.
pinshape
... ... **Thurbolt is a small start-up with huge dreams!! **We are currently building custom skateboard & esk8 decks, esk8 storage systems, custom electronics.. ...Check them out on www.thurbolt.com , instagram @thurbolt, youtube Kanber M.S.
thingiverse
here is a Universal Skate/longboard Handle, designed for Electric skate and electric longboard in mind, its designed so that it have little grooves/holes if you decide to glue it on your board instead of screwing it into your board (with is also...
thingiverse
Electric skateboard covers for concave deck * Dual VESC4 with capacitors and room for a receiver * The screwholes are designed for M4 7mm screws, but they are really lose (will upload a tighter version soon) for my print i melted M3 nuts into the...
thingiverse
I made this in two parts because all the other ones on here were not strong enough. ...make two end pieces and one or more middle pieces
prusaprinters
<p><strong>NOTE</strong>: I'll include photos of the board once its done, currently I just have parts so think of the current instructions as my plans. Ill update them and remove this note once everything is together!</p><p><strong>Story</strong>:...
thingiverse
DIY eSk8 Motor mount, adjustable v1. 4 piece mount. v2 will be 1 piece. ...Print Settings Printer Brand: RepRap Printer: ...
thingiverse
This is a simple voltmeter panel mount for an esk8 enclosure, includes cut template. ... Voltmeter: https://www.amazon.com/gp/product/B071HW4QHL/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
thingiverse
https://github.com/Mich21050/Brake_Lights/blob/master/README.md It's an open source PWM controlled brake light designed for esk8 in mind. ... Full credit goes to @mmaner
thingiverse
LP16 charge port cap featuring the PNW ESK8ing Sasquatch. TPU version has thicker walls, if printed in PLA or PETG it may be difficult to remove. The PNW_LP16.stl model has a thin wall to make popping it on and off easy, which will not print well in...
thingiverse
My take on an low poly skateboard / longboard / esk8 / electric skateboard wall mount. Pre-rotated for optimal strength, recommended at least 3 outlines and 20% triangular or grid infill. Flat head screws are recommended for mounting but...
thingiverse
You can read more about it there: https://forum.esk8.news/t/long-range-jump-emtb-swappable-12s3p-12s6p-dw-ii/51908 I designed it so that I could have modular batteries on my mountainboard. I wanted long range but also wanted to be able to jump...
thingiverse
Remix of another users (pathizar) ESK8 VESC CASE for layout needs, Check theirs for printable base and other lid/case options. I also have a lid in the works that will house the gotchipro from Derelict Robot Industries and allow the display to be...