esp-01 Enclosure Box

thingiverse

ESP-01 enclosure to use like a WIFI repeater (Github/martin-ger/esp_wifi_repeater).

ESP-01 Helper box

thingiverse

I made this "lower box" to make my unit last longer, its a very simple design so I used hot glue to mount the uart board and cyanoacrylate glue "crazy glue" to mount the esp-01 helper to the edge of the box. Other fun stuff at my personal...

ESP-01 electronics box

thingiverse

A nice electronics box for the ESP-01 wifi module with 5v-3.3v adapter. Original design can be found here: https://www.thingiverse.com/thing:3472764 Assembly: - The box is snap fit, not too tight, but depends if you have calibrated your e-steps :) -...

DHT11 indoor/outdoor sensor for esp-01 box with lid

thingiverse

I use a esp-01 (esp8266) module with a 120vAC-3vDC adapter and a DHT-11 Sensor. The box lid is tight enough to use ourdoor but not exposed to rain or water.For the power prongs I used the power adapters sold at the dollar store. Thanks, Enjoy! ...

ESP-01 Relay and HiLink power box

thingiverse

Simple box for esp-01 relay board with HLK 220V power. Added project in OpenScad for customizations. ... Project uses Round Corners Cube by Segio Vilches

2 relays box or ESP-01 with relay

cults3d

#2 relays box or ESP-01 with relay Links to materials: · 2 channel relay - http://ali.pub/42x6jz · ESP8266 - http://ali.pub/42x7ei Links to used tools: · Scrapers Deburring Trimming Tool - http://ali.pub/3wczyp · Tweezers - http://ali.pub/3ybjdx ·...

2 relays box or ESP-01 with relay

thingiverse

#3 relays box or ESP-01 with relay **Links to materials:** * 2 channel relay - http://ali.pub/42x6jz * ESP8266 - http://ali.pub/42x7ei **Links to used tools:** * Scrapers Deburring Trimming Tool - http://ali.pub/3wczyp * Tweezers -...

LiteArm / uArm control electronics box for MicroView + ESP8266 (ESP-01) board

thingiverse

This box mounts to the LiteArm i2 to house a PCB containing the servo headers and two LM2596 daughter boards with a MicroView (for servo and OLED display) and an ESP8266 daughter board for the ESP-01 to provide WiFi connectivity. The box mounts to...

ESP-01 Relay Module Case

thingiverse

... a while until I got a good result. (Seen here in blue.) The housing has a lid which can be clicked onto it. Printing: ESP-01 Relay Lid , 100% Infill needed, no supports. ESP-01 Relay Box , 25% Infill , supports for the Cable Holes. ...

ESP-01 Relay module

grabcad

There is CAD model of ESP-01 Relay module

ESP 01 Programming Cradle

thingiverse

So, I designed this little box that does all this for you, one side conencts to 3.3V power, the other to your PC using a serial adapter and in the middle you plug your ESP 01 board, the design is based on my previous ESP 01 Connector This box...

ESP 01 Connector

thingiverse

The ESP 01 Board (based on the ESP 8266) is tiny and cheap and a really good way to add WiFi capabilities to your project, however, it is also not solderless-breadboard friendly. This is a small connector that fits the ESP 01 board and is easy to...

ESP8266 ESP-01 Enclosure

thingiverse

Simple enclosure for a ESP8266 ESP-01 module with pins exposed to connect power and/or modules. This is my very first thing and I created it just to learn how SketchUp works. ... It's small and prints in just a few minutes.

ESP-01 Mouse Trap

thingiverse

The battery/ESP holder started out life as https://www.thingiverse.com/thing:535688, (thank you) with some modifications, there is a box on the bottom corner that gets removed to fit trap frame. I glued the whole thing together with PVC pipe...

WLED case (ESP-01)

thingiverse

This is a case for ESP01 controller for Led strip with button (on/off or change mode) Hardware: ESP-01s (With 1MB SPI Flash) Firmware: https://github.com/Aircoookie/WLED

esp 8266 box

thingiverse

esp 8266 box

Cover USB to ESP-01

thingiverse

Cover USB to ESP-01

ESP8266 ESP-01 Storage Magazine

thingiverse

ESP8266 ESP-01 Storage Magazine, stores 9 Modules. ... Inspired by the ESP8266 Storage Box by wraimann and a ammunition storage magazine.

EmonTX + Leonardo + ESP-01 Case

thingiverse

An enclosure for an electricity meter using OpenEnergyMonitor's EmonTX Arduino shield with an Arduino Leonardo and an ESP-01 module plus 5v adapter. I tried to make this as compact as possible but... in the end it's taller than I'd liked due to the...

ESP prog and ESP 32 box

thingiverse

ESP-WROOM programmer ESP-Prog Development Board JTAG Debug Program Downloader

ESP-01 5V Converter Enclosure

thingiverse

Simple enclosure to protect an ESP-01 plugged into a 5V regulator/level-shifter board. Allows convection cooling and isolates boards from metal. ... Designed with FreeCAD 0.19.

ESP-01 Antenna / LED cap

thingiverse

A little cap to protect an ESP-01's antenna, and also block the light from the LED. Prevents wild LED strobing during the night when lots of them are around, waking up from deep sleep regularly. I've noticed the board width can vary a bit, so it...

ESP8266 ESP-01 antenna improvement

thingiverse

If this improves a lot your ESP-01 performances (in my case file transfer speed got 10 times faster), then this thing should do a similar job. Not sure what this thing actually does, maybe it somehow shortens or modifies the antenna shape... ...BTW, if...

Esp 8266 nodemcu box

thingiverse

This is a box for a esp8266 with BME280 temperature,humidity and pressure sesnsor and ds18b20 temperature sensor

esp-32 box

thingiverse

printed box for ESP32-CAM. Nice fit. Two holes in the back for antenna and power cable. Holes for lid are 2 mm in diameter. ...I used salvaged screws of an old laptop.

ESP-01 IoT WiFi Button

thingiverse

I wanted a easy to do way if i needed to re-flash it, so the ESP-01 was the best and cheapest option. Just get it out of the Case again and put it on the programmer without the battery inserted, no need to desolder anything. (OTA Flashing wasn't...

ESP-01 Programmer case (SCAD)

thingiverse

Just my design of an ESO-01 USB Programmer case. ...Super Simple.

ESP 8266 dev storage box

thingiverse

Storage box for two esp 8266 dev modules

relay module box with esp

thingiverse

This is my first published project, it is a simple box for a relay module with an ESP 01, the printing configuration is simple. The drills are for 2mm diameter screws. ... I have designed a small wiring support to give the whole more confidence.

Case Module ESP8266 ESP-01 Relay

cults3d

The Case ESP-01 relay is composed of a rectangular-shaped box divided into two parts with the following dimensions: Inner side ESP-01 Relay Plate Length: 26.50mm Width: 38.50mm Height: 18mm Inner side Cell Source Board (Optional) or 100-240V AC to 5V...