esp 01 programming 3d models

So, I designed this little box that does all this for you, one side conencts to 3.3V power, the other to your PC using a serial adapter and in the middle you plug your ESP 01 board, the design is based on my previous ESP 01 Connector This box...

Very simple programming jig for ESP12 or TYWE3S. Uses 22AWG solid core wire. Use a small spring clamp to hold in place. ... Inspiration from digiblurDIY: http://y2u.be/qMpKzZHSh2Q

Previous version available at: https://www.thingiverse.com/thing:3229822 Programming jig used to mount/align pogo pins for programming ESP8266 or TYWE3S such as used with WiFi home automation controllers and other DIY microcontroller projects. ... ...

Jig for programming TYWE2S. Add pogo pins. Included part with 1.0mm holes and 1.4mm holes for pins, drill and/or glue might be needed. ... pogo pins used https://www.aliexpress.com/item/1005002667659397.html

Programming jig used to mount/align pogo pins for programming ESP8266 or TYWE3S such as used with WiFi home automation controllers and other DIY microcontroller projects. Designed in SolidWorks. i have two sizes for different sized pogo pins or...

ESP-01 enclosure to use like a WIFI repeater (Github/martin-ger/esp_wifi_repeater).

There is CAD model of ESP-01 Relay module

This is a case for ESP-01 Adaptor. ...To add WIFI to Anycubic Mega S

This is a precision-fit housing for the relay module with ESP 01/s. ...The reset button can be operated from the outside.

ESP 01 Relay enclosure. It has a nice cable management hole so your wire can run from inside and no connections would be visible externally. If using with ESP 8266 you can use the normal lid. If you want to control LED or anything from raspberry...

I made this "lower box" to make my unit last longer, its a very simple design so I used hot glue to mount the uart board and cyanoacrylate glue "crazy glue" to mount the esp-01 helper to the edge of the box. Other fun stuff at my personal...

Simple enclosure for a ESP8266 ESP-01 module with pins exposed to connect power and/or modules. This is my very first thing and I created it just to learn how SketchUp works. ... It's small and prints in just a few minutes.

The ESP 01 Board (based on the ESP 8266) is tiny and cheap and a really good way to add WiFi capabilities to your project, however, it is also not solderless-breadboard friendly. This is a small connector that fits the ESP 01 board and is easy to...

A nice electronics box for the ESP-01 wifi module with 5v-3.3v adapter. Original design can be found here: https://www.thingiverse.com/thing:3472764 Assembly: - The box is snap fit, not too tight, but depends if you have calibrated your e-steps...

A nice electronics box for the ESP-01 wifi module with 5v-3.3v adapter. Original design can be found here: <a href="https://www.thingiverse.com/thing:3472764">https://www.thingiverse.com/thing:3472764</a></p><p>Assembly:</p><ul><li>The box is snap...

This is a case for ESP01 controller for Led strip with button (on/off or change mode) Hardware: ESP-01s (With 1MB SPI Flash) Firmware: https://github.com/Aircoookie/WLED

The code is very simple, just contact IFTTT with your account and trigger your applet and go to deep sleep with no wake ESP.deepSleep (0), I discovered a flaw in the ESP mounting, will work fine if its in the house in a second floor or on a shelf,...

Cover USB to ESP-01

A box to attach to the din rail for an ESP-01 based circuit. ... Inside, ESP-01 is powered by a 3.3V transformer. ... The parts are to be attached with 3mm self-tapping screws.

Simple enclosure to protect an ESP-01 plugged into a 5V regulator/level-shifter board. Allows convection cooling and isolates boards from metal. ... Designed with FreeCAD 0.19.

ESP8266 ESP-01 Storage Magazine, stores 9 Modules. ... Inspired by the ESP8266 Storage Box by wraimann and a ammunition storage magazine.

... for PIR sensor. ... Update: Added a down-looking-sensor version as well as a shield that can be glued on to block motion from certain sides. PIR https://www.amazon.com/dp/B096NZ4P3K Shield https://www.tindie.com/products/serg74/esp-01-wled-shield/

... a while until I got a good result. (Seen here in blue.) The housing has a lid which can be clicked onto it. Printing: ESP-01 Relay Lid , 100% Infill needed, no supports. ESP-01 Relay Box , 25% Infill , supports for the Cable Holes. ...

Case for ESP-01 and holder on the Ender 3 printer. ...</br> Two holes for LEDs, without screws.</br> If you are interested in instructions on firmware and connection, then write in the comments

This is a small case for this ESP-01 programmer: https://www.amazon.de/gp/product/B09DYGB6FYIt just snap-fits together.

A little cap to protect an ESP-01's antenna, and also block the light from the LED. Prevents wild LED strobing during the night when lots of them are around, waking up from deep sleep regularly. I've noticed the board width can vary a bit, so it...

An enclosure for an electricity meter using OpenEnergyMonitor's EmonTX Arduino shield with an Arduino Leonardo and an ESP-01 module plus 5v adapter. I tried to make this as compact as possible but... in the end it's taller than I'd liked due to the...

If this improves a lot your ESP-01 performances (in my case file transfer speed got 10 times faster), then this thing should do a similar job. Not sure what this thing actually does, maybe it somehow shortens or modifies the antenna shape... ...BTW, if...

I wanted a easy to do way if i needed to re-flash it, so the ESP-01 was the best and cheapest option. Just get it out of the Case again and put it on the programmer without the battery inserted, no need to desolder anything. (OTA Flashing wasn't...