esp32 cam case battery 3d models

Battery Case

A simple Case for the ESP32 NodeMCU Module WLAN WiFi

This is a tiny case to hold a mini ESP32 (Wemos D1) and an HLK LD2410C mmWave sensor. ... Fusion 360 project included.AA Battery in picture for scale (I didn't have a coin handy

another lightweight bracket for a water meter. Esp32-cam has to be mounted using a ziptie (one day I'll adapt to use the housing from jomjol). Two LED holes are available, allthough I am not using them for now I also included an image of my...

You can find the source code to the firmware at https://www.makersmashup.com/downloads/9f1c1e46-5636-47b1-b3cc-13178671620f The ESP32-CAM is available at https://amzn.to/32z7O0L You'll also need a Serial to USB Converter, which can be found at...

This IP Camera does not have that limitation and works perfectly with Octoprint. I have a complete how-to video on how to get it running here https://youtu.be/6qiH1BRwUeA?sub\_confirmation=1 It uses a $10 ESP-32 Cam development board which works...

Remix of LayneBernardo ESP32 case design, increasing the spacing for ESP32 board with pins and added screw brackets.

You can then power your OpenMV Cam from the battery and the PoE shield at the same time for a battery backup, and the case comes with a cover to put over the exposed wire.Your PoE shield should come with the required mounting hardware to use the...

M5 Stack Timmer Cam mountRemixThis can be used to attach the Timmer Cam to a camera mount.Requires the timmer cam cover (normally included with the camera).This is a press-fit design, but added holes for an M3 bold.

A simple two part case for a 4.2 inch epaper display, ESP32 board, and Lipo battery. The USB connector is sunk in because on the ESP32 board I'm using, a "WEMOS LOLIN32 ESP32 Lite", the Lipo connector (for some silly reason) faces the same way as the...

Thanks mojocorp for the great case design. I added a GoPro type mounting as described in https://www.thingiverse.com/thing:4072374 and I extend the case to fit for a ESP32 CAM with an attached programming shield (ESP-CAM-MB). The shields usb is...

**Camera Settings** * `esp32_camera:`: This section configures the camera settings: + `external_clock`: This defines the external clock source for the camera, which is connected to pin GPIO0 with a frequency of 20MHz. + `i2c_pins`: These define the...

This is a case for an ESP CAM 32.

Remixed from both https://www.thingiverse.com/thing:4702089 and https://www.thingiverse.com/thing:3652452 I have modified the mount so the esp32 camera can mount directly to the camera mount

Youtube - https://youtu.be/MjU-A8bGOjoESP32 CAM - https://bit.ly/3tujOD4Arduino TT motor - https://bit.ly/48QMfexMotor driver MX1508 - https://bit.ly/3LZ80iv18650 LI-ion - https://bit.ly/3PVadg2USB type-c charger - https://bit.ly/3rFre65DC-DC Mini360...

This is a Case for the ESPSomfy-RTS project with a 30 pins ESP32 Development Board.

A case for an 8 channel relay board with space for an ESP32 and power supply.

This is the case that houses the esp32 and USB host shield.

Simple case for a DOIT ESP32 DevKit V1 36pins devboard. ...Top press fits on bottom part.

Video: Guide: https://learn.adafruit.com/feather-tft-stemma-case3D print a Stemma case for the Adafruit TFT Feather with ESP32-S2.TFT Feather ESP32-S2https://www.adafruit.com/product/5300BMP280 Stemma QThttps://www.adafruit.com/product/2651Stemma QT...

Video: Guide: https://learn.adafruit.com/feather-tft-stemma-case3D print a Stemma case for the Adafruit TFT Feather with ESP32-S2.TFT Feather ESP32-S2https://www.adafruit.com/product/5300BMP280 Stemma QThttps://www.adafruit.com/product/2651Stemma QT...

Minimalistic case for MakerFabs ESP32-S3 Parallel TFT with Touch 3.5'' module https://www.makerfabs.com/esp32-s3-parallel-tft-with-touch-ili9488.html Remixes welcome!

A simple ESP32 surveillance Camera case with Antenna Easy to print Parts you need: - 1x ESP32 Camera https://de.aliexpress.com/item/1005001322358029.html - 1x ESP32 Antenna https://de.aliexpress.com/item/4001054693109.html

just battery case

This is a fork from @nieleyde (Lolin32, Ultrasonic Sensor, & Battery Case). I have generously enlarged the hole on the sides, so that almost any mini usb cable fits inside In addition, I have also made a hole on the other side, so that you can put...

I simply added some air vents to help prevent overheating, and a hole at the bottom to mount a micro USB breakout board (the green version) so that you can pwoer the cam with a standard micro USB charger.

This is a case and mount designed specifically for the TTGO T-Journal ESP32 Camera board equipped with a fish-eye lens, available on Aliexpress at...

I just cut the holder for the tripod and put it to the small side. ...My ESP32 cam software does not allow to rotate the picture by 90 degrees.

Inlay for the GoPro Case (that comes with the GP9 & 10) allows you to store a GP9/10 + GP3/4 + Insta360go/Insta360go2/Caddx-Peanut Allows you to store ND-Filters and Batteries Allows you to place a power bank underneath and recharge your cams while...

https://youtu.be/nKFDXzp5-So Guide: https://learn.adafruit.com/feather-tft-stemma-case 3D print a Stemma case for the Adafruit TFT Feather with ESP32-S2. This dev board features a 1.14 inch display with a Lipo battery charging circuit and battery...