esp32 cam case 3d models

In this case, the cable should be routed differently or a thinner cable should be used.I have switched the ESP Sketch to continuous LED on and HD image (720) directly from the boat.GERMANFür alle, die wie ich, nicht 100% glücklich mit der...

https://www.twitch.tv/webranger Thank you very much for that I use this esp32 cam module =>...

(Imported from Thingiverse)A case for the ESP32 Cam board that has no lid, the board snaps in with little force. It has 3 mounting points, with 2 holes each. There is a version for M1.5 (1.75mm) and one for M3(3.25mm). The holes are 14mm apart. This...

One of the annoyances I've discovered with ESP32-CAM boards is that the cameras are not uniformly aligned; what is “up” for one unit is not “up” for another.  This in turn has made getting a case I like difficult.  So I made my own.The case...

So I designed this case to hold an ESP32 Camera, a 10x30 Radial Fan, and an external antenna. The back has a ball fitting for an articulated arm or whatever fitting you figure out. You can print without supports, or use small ones for the...

To fit my Cam-Module from DM (diymore.cc), I moved the camera hole 2 mm outwards and the light hole 1 mm inwards. SD-Card slot is optional. The back was modified to hold my different USB-board (see picture). Design changes were made with fusion360. ...I...

... side. ... The micro USB board holder broke immediately, so I drilled two holes into the case and secured it with 2mm plastic screws. ...If you need some code for timelapse recording, check out this repository: https://github.com/Radla/esp32cam-webcam

I liked Kosec's ESP32-CAM case but it didn't quite fit the ESP32-CAM board I had (they seem to vary a bit) so I tweaked the lens and flash hole positions, added a hole for a power lead and a small bulge to allow an SDCard to be used. The snap-on...

The USB part is not modified so should be taken from the original ESP32-CAM Case of AI on the Edge or the remix from hackup. I have added an alternative cover that leaves more room for wires from the USB break-out to the supply pins of the...

<p>Remix of the back cover to fit my USB breakout board. There seems to be a few different versions, most commonly one with a blue PCB and another with green. ...The original design seems to be fitted around blue, but mine was green so a quick remix to...

Remixed From: https://www.thingiverse.com/thing:4846885 in Tinkercad There ist the Tripod Stand. ... Now my ESP32-CAM fits into Case. ... ESP32 Cam WiFi Bluetooth Development Board mit OV2640 Kameramodul + Micro USB zu seriellem Port CH340C

ESP32-CAM WROVER用のケース * 更新履歴 * 2023/08/27 ESP32-CAM1_WD_Body.stl LCD確認用穴追加、タクトスイッチ穴位置微調整 * 2023/06/08 STLファイル名統一 本体のガイドレールが基板と干渉して蓋が完全に閉まらない場合がある対処(ESP32-CAM1_WD_Body.stl) * 対応機種 * Freenove ESP32-WROVER CAMボード...

I like the simplicity of Carsten's ESP32 Cam Clamp and how it holds the camera in place. However, I wanted it to fully cover the front and use it with a <a href="https://www.aliexpress.com/item/1005003279204315.html">120 degree wide-angle lens</a>,...

ESP32-CAM case. ...Without SD-card hole.

# EN I wanted to design a ESP32-Cam case with tripod as a week-end project. The tripod is single part printed. I print with .8mm nozzle and .3mm layer height 3x M4 nuts + 1x M4L20 screw required OnShape Link :...

ESP32 CAM Camera Case with 3 axes of rotation Cura's parameter:  - No support - Standard quality: outer body (corps_ext), bond (liaison), front panel (face avant) - Dynamic qualitiy (or better Super Quality): rear panel (face arrière), inner body...

... surveillance environment ist MotionEyes (on Raspberry Pi 3). Firmware and further instructions for RTSP-Streamer ESP-32 Cam can be found on https://bitsnblobs.com/rtsp-video-streamer---esp32/ https://github.com/bnbe-club/rtsp-video-streamer-diy-14

Remix of https://www.thingiverse.com/thing:3876150/files with crude cut-outs to allow fitting of the ESP32-CAM-MB inside the case. ... Using the mount arm from this thing: https://www.thingiverse.com/thing:334100

... fan. The case also features a small hole for the led light of the esp32-cam. The stand is a remix of https://www.thingiverse.com/thing:4107609 thank to @MagnusT. ... Added a new case and stand with holes for screws (I use nylon screws and nuts)

Minor modification of the ESP32-CAM with tripod, added some vents on top when I noticed the original case became warm, added an SD slot hole, and a reset button hole.... ...also made the flash hole a bit wider as I noticed it was a bit off to the left.

This is a case for the ESP32-CAM module. It has been remixed from [the case](https://www.thingiverse.com/thing:4571627) that is intended to plug onto the various [AI-on-the-Edge](https://github.com/jomjol/AI-on-the-edge-device) contraptions. I had...

Well i needed a simple case with slots for both the micro SD card and the LED lamp for the ESP32-CAM module. It does not fit the USB programmer. But it has enough room for Dupont connectors to supply it with power. Clearance is tight so your...

Added cooling slots in the front and rear parts of JPGuitar's mount for the ESP32-Cam. I also slightly increased the size of the cutout for the hex nut for a better fit. The 3mf contains gabr42's improved x-axis base, so all parts needed to mount the...

Housing crafted specifically for ESP32-cam modules, featuring precision-cut holes to accommodate 5 mm infrared LEDs in sets of three.\r\nA dedicated LED compartment securely holds the LEDs and resistor within its confines, while a partition separates...

The mounting block itself should be screwed to the back cover of the case using a 2.5mm screw and double-sided mounting tape, or just glue it together.The case leaves clearance for the connector pins, and the mounting block leaves just enough...

I'm particularly fond of the straightforwardness of this scenario, which prompted me to reimagine it entirely and create an opening for the external antenna. ...In addition, I modified the camera slot to a square shape to enhance its compatibility.

Use this part (and you need some more) to mount it on your Prusa MK3 printer.

Olá, esse é um projeto em progresso. Alguns detalhes ainda não estão perfeitos tudo encaixa mas ainda há melhorias possíveis. ...

Easier to mount. ... Category: Electronics

I moved the antennae bracket to make it a bit more compact, plus rounded up the edges a bit more and re-positioned the micro SD card slot for a better fit. I've included a plain back; plus one with a bracket, which I hope fits a GoPro style mount...