esp32 camera pir 3d models

ESP32 CAM Camera Case with 3 axes of rotation Cura's parameter:  - No support - Standard quality: outer body (corps_ext), bond (liaison), front panel (face avant) - Dynamic qualitiy (or better Super Quality): rear panel (face arrière), inner body...

This is a simple ESP32 Camera mount that will bolt up to the corner of your CR-5 Pro or CR-5 Pro H. There's some modifications to the housing, created by laisch (see remixed from), that allows a 2 pin Dupont connector to be used to power the camera,...

AIOCam - Cab designed to house a Micro 5.8ghz FPV Camera, instead of an ESP32. V5 - Narrower, wheels set inward to reduce stress on servo shaft. AIOCam - Cab designed to house a Micro 5.8ghz FPV Camera, instead of an ESP32. AltCOG - Alternate Chassis...

(SINGLE AND DUALCOLOR VERISON IN THE FILES) I used these threded inserts: https://www.aliexpress.com/item/1005005083203380.html?spm=a2g0o.order_list.order_list_main.98.1d821802gb8ysK I used this IR LED camera ring:...

Unscrew and discard camera lens (sharp knife, engineers pliers) Remove and discard IR filter disk (tweezers) Re-connect camera module with ESP32 Upload Software For the first tests and most purposes the arduino demo sketch will do. There are many...

The esp32 cam usually ships with 66 degree camera which wont work for spotting scopes. Any ov2640 above 66 degree cannot be used on the spotting scope. I have tried them and they don't work for capturing the image from the eye piece. I have...

Thanks mojocorp for the great case design. I added a GoPro type mounting as described in https://www.thingiverse.com/thing:4072374 and I extend the case to fit for a ESP32 CAM with an attached programming shield (ESP-CAM-MB). The shields usb is...

I brought home a low-cost ESP32-CAM board and started to play around, then it became apparent that adding an additional lens in front of the camera would make it an excellent macro unit. All well and good, but not so easy to hold stable, so I set...

This is a revised version of the [Replacement Lid for 100x68x50mm (3.9"x 2.7"x 2") Waterproof (IP65) Project Box] model, modified to accommodate an Hi3518 camera module and HC-SR501 PIR sensor. Note that you will need to download the SCAD files...

This modification is specifically designed for Ender 3 printers, allowing users to easily integrate a low-cost Wi-Fi camera. To complete this setup, you'll need a screw to secure the joint between the lid and arm, as well as longer screws than those...

A case you can use to attach ESP32-CAM to your CNC1310's X axis. ...It requires you to run a 5V cable from the main board to the ESP32-CAM (there's a free 5V connector on the board already)

This is a simple camera mount for ESP32-CAM. It can orientate any position and wall mount or flat surface mount. V2 is a ring more, that you put before on the base, after you connect the case, and finally put up the ring to straighten! So no more...

I'm currently attaching a stepper motor mount to enable mounting the camera on a 3D printer's axis. ... You can locate the accompanying video at https://youtu.be/9tq5j6w7h8g .

ESP32

esp32

ESP32

esp32

Buy your TTGO T-Camera from this link: https://www.aliexpress.com/item/TTGO-T-Camera-ESP32-WROVER-PSRAM-Camera-Module-ESP32-WROVER-B-OV2640-Camera-Module-0-96/32968683765.html The STL files for the case are available in both fisheye and regular...

ESP32-WROOM-32 is a powerful, generic Wi-Fi+BT+BLE MCU module. At the core of this module is the ESP32-D0WDQ6 chip. ...The embedded chip is designed to be scalable and adaptive.

ESP32 Detailed Model for Reference. ... This detailed model showcases a customized NodeMCU ESP32S design, serving as a precise guide for crafting a tailored housing solution. ... Dimensions: - Length: 49.5 mm (includes USB port) - Width: 25.9 mm

Case and camera clip for the Freenove Breakout Board for ESP32 / ESP32-S3 WROVER WROOMThe separately printable clip, which clips over the processor board, can be used to adjust the angle of the camera.

This is ESP32 development board with built in 3.5" TFT LCD Touch screen and OV2640 camera.

This is ESP32 development board with built in 3.5" TFT LCD Touch screen and OV2640 camera.

Simple minimal holder for ESP32 CAM - with standard camera tripod screw thread. ... https://a360.co/3qqz395

Based on the original curved case by 'pcky' i have added a socket on the back cover and two different ball socket mounts. One for standing on a table/desk the other for mounting to a wall. There is also a variation with a hole in the back cover which...

... parts from the Thingiverse model at https://www.thingiverse.com/thing:4293961. I used the software from Hackaday.io project #168563, "ESP32-Cam Example Expanded", to control the camera. ...This software also allows you to manage the LED light.

This is a case for the ESP32 Camera and a pair of 5mm IR LEDs (or normal LEDs) be aware that the IR filter on the lens must be removed in order to convert the camera to night vision. The process is not without risk, as you can easily destroy the...

Hello, This is a compact camera mount designed specifically for the ESP32-Cam: http://www.thingiverse.com/thing:3463679, courtesy of Mojocorp. I've remixed it to accommodate a tiny cam like the ESP32-Cam. I modified the sketch from v12345vtm:...

This is a case for the ESP32 Camera and a pair of 5mm IR LEDs (or normal LEDs)be aware that the IR filter on the lens must be removed in order to convert the camera to night vision. ...The process is not without risk, as you can easily destroy the small...

This is a simple case for your ESP32-CAM board including optional hole for mounting external antenna. You can easily rotate the camera in 360°. The mounting system has a small "flap" on site. It is designed to be clamped to a window between the...