esp32 case 3d print

*NOTE: If your battery has a JST 1.25 connector already, check the polarity carefully with the cable included in the TTGO board.* ## Parts * **TTGO ESP32 T-DISPLAY:** https://s.click.aliexpress.com/e/_ADirut * **Battery:**...

The scenario involves integrating ESP32, DHT22, and MQ-135 into the same housing unit, but this setup poses challenges due to the MQ-135's tendency to overheat, potentially damaging the DHT22 sensor on the opposite side of the case. To assess the...

This is a case for the ESP32-CAM module. It has been remixed from [the case](https://www.thingiverse.com/thing:4571627) that is intended to plug onto the various [AI-on-the-Edge](https://github.com/jomjol/AI-on-the-edge-device) contraptions. I had...

This is a case for the version 2 of the TTGO ESP32 LoRa development board with external antenna. Inside, you can fit a small LiPo battery. From the case, you have access to the Reset button, power on/off and the SD Card slot. You will need three...

Modifications: - Slightly resized to accept the D1 ESP32 module (which is bigger than the 8266 version) - it sticks out about 3mm more. - The RS485 board has moved to the back by 3mm, so now fits only without the screw terminals. - The small clips...

You may need to re-size/check the carrier dimensions depending on your own ESP32 board. I designed this to use with Jumper cables, i didn't have a screw for the DHT sensor so i used 3m adhesive in its place. 3m Adhesive on the jumpers on the...

I use this case as a sensor box for ESP32 Wemos D1 from AZDelivery with an BMP280 sensor. Wemos itself has no screws so its laying just inside. The distance between the holes is 10mm, which seems to be suitable for many types of sensors. The...

... board should have been approximately 23.50 mm and 50.90 mm between the screw holes (midpoints). If you utilize a development board with different dimensions and require a customized case, please post the distance of the screw holes in the comments.

Case for the ESP32 D1 mini and a TFT 3.2 inch (ILI9341). I designed this to connect a ham radio transceiver FT-817 or FT-818 to the display. The USB port of the ESP32 will later only be used for programming, while the cable on the back is connected...

Buy your TTGO T-Camera from this link: https://www.aliexpress.com/item/TTGO-T-Camera-ESP32-WROVER-PSRAM-Camera-Module-ESP32-WROVER-B-OV2640-Camera-Module-0-96/32968683765.html The STL files for the case are available in both fisheye and regular...

... prefer it to do.The enclosure designed to loose fit, because I like the easy access. If you prefer a snug fit print the center part at 101% size.Print instructions:Material: PLA / PETGLayer height: .2Perimeters: default settingsSupports: not needed

I needed a highly durable case that could also accommodate my 380mAh lipo, so I built this case. The pcb sits firmly in place, thanks to thick walls and a loop that allows you to hang it on your backpack securely. It uses 4 m2*12 screws, but a few...

This is a case for the ESP32 Camera and a pair of 5mm IR LEDs (or normal LEDs)be aware that the IR filter on the lens must be removed in order to convert the camera to night vision. ...The process is not without risk, as you can easily destroy the small...

This is a very close 3d board model for a Turkish esp32 board named Deneyap Kart. ... ** Check our products on www.sundaykits.com now.

... PIR HC-SR501. Micropython code for the ESP32 at https://github.com/divergentti/kotiautomaatio/tree/master/esp32/liiketunnistin Another design for ESP32-Wroom-32 without external antenna is available too, but perhaps this version is better overall.

... PIR HC-SR501. Micropython code for the ESP32 at https://github.com/divergentti/kotiautomaatio/tree/master/esp32/liiketunnistin Another design for ESP32-Wroom-32 without external antenna is available too, but perhaps this version is better overall.

screw the ESP down to the mounting posts with two M3 x 6mm screws (go back in time and connect the ESP board to your screen and test it) fit the screen into the case and glue it to the support shelves test fit the bezel, if it all seems good, glue it...

I used: - 2 of 12mm disc magnets (thin, 1 or 2 mm) - A TTGO Mini32 dev board because it's quite small and has built-in Lipo charge circuitry - A spare 600mAh battery with protection circuit - A 2.9" ePaper module - My favorite green PLA Simple...

Well i needed a simple case with slots for both the micro SD card and the LED lamp for the ESP32-CAM module. It does not fit the USB programmer. But it has enough room for Dupont connectors to supply it with power. Clearance is tight so your...

Simple case for the new ESP32-C3-12F-Kit board, with glued on USB-A connector for power like in the picture. Adjust the placement of the opening if you like it otherwise. Both parts friction fit together and hold the board firmly. No screws needed.

Simple case for the new ESP32-C3-12F-Kit board, with glued on USB-A connector for power like in the picture. Adjust the placement of the opening if you like it otherwise. Both parts friction fit together and hold the board firmly. No screws needed....

I'm working on a two-part casing project for my TTGO Esp32 development board, but I still have some work to do before it's complete. In fact, I've already repurposed two of the buttons for another project, so I'll need to update this model once my...

The ESP32 case is one of a series of accessories which I'll be adding to my design portfolio for general purpose micro-controller project use. Completed projects using these components may eventually be made available with code posted on my own...

https://www.youtube.com/watch?v=n6k_8D885sE This is a case for the version 2 of the TTGO ESP32 LoRa development board with external antena. Inside you can fit a small LiPo battery. From the case you have access to the Reset button, power on/of and...

This is a case for the TTGO version 2.1 ESP32 LoRa development board with external antenna, designed specifically for the ESP32-Paxcounter project on GitHub. The case provides full access to all connectors and the reset button, ensuring seamless...

In my experience, two 500mAh batteries (combined 1Ah 3.3V) last for three months provided that they don't get drained when there's no WiFi or Internet and the ESP32 is constantly attempting to get data. To protect your cells from over-discharge, I'd...

Youtube - https://youtu.be/MjU-A8bGOjoESP32 CAM - https://bit.ly/3tujOD4Arduino TT motor - https://bit.ly/48QMfexMotor driver MX1508 - https://bit.ly/3LZ80iv18650 LI-ion - https://bit.ly/3PVadg2USB type-c charger - https://bit.ly/3rFre65DC-DC Mini360...

2021) of the popular ESP32 Weather Station Case! Changes: improved case design: - hole for micro USB for charging and indicator LED - improved design of the back cover This is a case designed for 4.2" E-Paper or E-Ink Displays. It can be used as a...

My first project was a temperature/humidity/pressure sensor, packaged into a case with a small display to put in on a shelf or cupboard. ... ESPHome: https://esphome.io/index.html# Home Assistant: https://www.home-assistant.io/ Board:...

My first project was a temperature/humidity/pressure sensor, packaged into a case with a small display to put in on a shelf or cupboard. ... ESPHome: https://esphome.io/index.html# Home Assistant: https://www.home-assistant.io/ Board:...