esp32 feather 3d models

ein Einfaches Case für einen DHT22 und einen ESP32. Die 4 anschlüße sind einfache JST BEC Stecker. ...Platz und ein Fenster für eine 5mm Anzeige LED ist auch vorhanden.

This is a remix of ESP32 DevKit V1 Case (Thick). ...The only difference is that both parts now lay flat on the bed rather than 1cm in the air for the top.

ESP32 controller have a wide pinout, which doesn't fit into standard breadboards. Here, a small 30 pin breadboard has been cut into 2 parts. ...To hold them in the right distance together, this holder has been designed.

**Parts:** * 1x ESP32 Devkit V1, available at https://www.banggood.com/ESP32-Development-Board-WiFibluetooth-Ultra-Low-Power-Consumption-Dual-Cores-ESP-32-ESP-32S-Board-p-1109512.html?rmmds=search&cur_warehouse=CN * 1x BME680 Sensor, available at...

OV2640 Camera Module for ESP32 CAM Camera Module 2MP 160° (120°) 850nm Night Vision https://www.aliexpress.com/item/1005003040149873.html?spm=a2g0o.detail.0.0.239c8CDR8CDRKv&mp=1

This is design to work with a MG90S servo motor and the ESP32-Cam case designed by SolarGermany https://www.thingiverse.com/thing:3949787/makes Demo: https://youtu.be/v_A3rCVCbVE

I remixed it in order to - have less parts to print - avoid the requirement of supports - make use of a ESP32-CAM-MB module which has USB on board for power and programming Downside is that you now need some screws to put it together. You will need:...

Case and mounting bracket for a 180-degree rotatable webcam, consisting of an ESP32-CAM module and an RC servo. ... The related software and further details on the project can be found at Github (https://github.com/HenrikAalto/RotorCam180).

This is a case for an ESP32-DevKitM-1. It retains access to the pin headers. ...The case is designed to be printed without supports and the lid is fixed with two M3x8 screws.

This design encloses the ESP32-Cam, serving as a housing for the device, essentially a surveillance camera. If you find this model helpful, consider following me on Instagram at thiago.electric to access additional designs. ...Thanks for your interest!

A simple housing for an ESP32 controller, comes with 2 flavors with the diffrence being one has a "tunnel" open up to the lid and one only has a hole for the cables to run through.

Original Authors BlogOriginal Model Source

To fit AZdelivery board https://www.amazon.se/dp/B08BTWK3VV?ref=ppx_yo2ov_dt_b_product_details&th=1AZDelivery 3 x ESP32 NodeMCU D1 R32 WlanUsed in WLED projects

Waveshare's ESP32-S3 Zero board, 4MB FLASH & 2MB PSRAM, castellated pins, USB-C receptacle and SMD antenna.Note that the fanout pads aren't apparent in this model.

Useful universal attachment method to hold OLIMEX esp32-PoE-ISO Need revision (enlargement of base hole) for SD card slot use. Printed on prusa mini 0.25mm w. ...20% infill in prusament galaxy black Snap fit design.

Servo 12 Pcs Esp32 Batre PLA Filament https://www.youtube.com/channel/UCuD8szgWX1oVhFmXELxeZ7Q https://youtu.be/atfthhu9rWo https://youtu.be/4OahFHEhecs https://youtu.be/n7vpWb9VptA https://youtu.be/vJSkAeb74VQ

This is a dimensionaly accurate model of the board, meant to help in designing stuff around it. ...Not every single component has been modeled, but the most critical, function/dimension wise.Used models:ESP32 WROVER BBATTERY HOLDER

The ESP32 WROVER B is a microcontroller module that combines the popular ESP32 chip with 8 MB of external flash memory and a PSRAM (Programmable Serial RAM) module, providing users with an ample amount of storage space for their applications. This...

Basic case for ESP32 XC3800 module. This module is equipped with headers. Case is for usage with module only, e.g. ...ESP Presence or ESPHome Bluetooth proxy.</p>

Laptimer Case for the FPVSIM Laptimer 4.0, to protect the ESP32 and RX5808.Hole for USB-C for power.Top cover can be screwed to the base with M2 and glued too.

Din Rail Mount for ESP32. Everything except printed part is from Aliexpress. ... [Din Rail Mount for ESP8266](https://www.thingiverse.com/thing:5849218) [Din Rail Mount Raspberry Pi Pico](https://www.thingiverse.com/thing:5917695)

PARTS NEEDED:AWOK ESP32 V4 BOARDM3 10MM X 4PCS*I have found I get the best results with no part cooling for the first few layers to avoid edge warping, personally I don't cool for the first 8 layers.

A case for a ESP32_camm with space for a 18650LiPo-cell and a TP4056 MicroUSB charger module. ... I drilled the hole for the switch after printing, so it is not in the model and are optional.

This is a camera case made for the Arduino ESP32 CAM bought on Banggood. No need for supports or rafts. Please change filament temperature and speed since the base material i used was PETG. ... Prints in about 2h.

This is a remix of "esp32 cam mount for ender 3 v2" by wenbozThis version has a 5 degree angle in order to keep the camera pointed at the print

... was found on Grabcad. Thanks to Jan Jazek for providing it! Link: https://grabcad.com/library/esp32-cam-1Print SettingsPrinter Brand:Prusa Printer: I3 MK3SRafts: No Supports: NoResolution: 200 Infill: 20Filament:Prusa PLA    Category: Electronics

A case for the esp32 webradio project from "AZ Delivery": https://www.az-delivery.de/blogs/azdelivery-blog-fur-arduino-und-raspberry-pi/internetradio-mit-esp32-und-max-98357a Just glue the Poti_Logos file on the Poti knobs with plastic glue. For...

Parts: 1x ESP32 Devkit v1 (eg https://www.banggood.com/ESP32-Development-Board-WiFibluetooth-Ultra-Low-Power-Consumption-Dual-Cores-ESP-32-ESP-32S-Board-p-1109512.html?rmmds=search&cur_warehouse=CN) 1x BME680 Sensor (eg...

ESP32-3248S035 "Cheap Yellow Display" 3.5" TFT with capacitive touch-- model isn't perfect but I measured everything with decent calipers so it shouldn't be far off.

We've just added the ESP32 label to the project. To make room, we've taken out the inside pin holders. ...We've also widened the top section slightly to ensure a snugger fit.