esp32 nodemcu 3d models

When printing the packers you may need to enable thin wall detection or Arachne slicing in order for the small top ring to print properly.Follow the coding instructions on the GitHub page to setup the controller.In your config_buttons.h file you will...

Rui Santos gives a good introduction to the Node Red setup.https://RandomNerdTutorials.com/esp32-mqtt-publish-bme280-arduino/The Fusion 360 file https://a360.co/3jyALCo for the ring is included with the formula to calculate diameter for different...

I used an ESP32 board (**38-pin version**) to decode the PWM signals from an 8-channel 2.4GHz receiver and control the vehicle accordingly. The coding was done in the Arduino IDE. Each of the four legs consists of a shock absorber, a carbon fiber...

For electronics, two 3mm LEDs (red and green) are required, along with a microcontroller to drive your display – I used an ESP32 and ESP8266. Mounting inserts for common .96" and 1.3" OLED modules from Amazon or Aliexpress have been included in the...

But the amount of filament is only 170 gram per batch, so 340 gram in total.It uses 65 led per strip coming at around 65 led 4 30mA = 10,4 Amps of power needed.Yesterday I moved to esp32 with Wled (https://github.com/Aircoookie/WLED/wiki)Just hook up...

OpenRC 4-Wheel Drive Go-Kart with Ackermann SteeringThe model is inspired by Lego Go-Kart 1972:https://www.toysperiod.com/lego-set-reference/technic/model/race/lego-1972-go-cart/The custom electronics has been designed around the Esp32 processor. The...

It is connected to an esp32 processor with a display that shows the remaining weight of the filament that is left on the spool. Spools are numbered and the esp32 remembers the weight if the spool is changed with another one. Using the knob and...

This will give them sufficient sturdiness.PARTSStencil Sheet Diffuser - https://www.hobbylobby.com/Crafts-Hobbies/Craft-Paint-Stencils/Stencils/Stencil-Blanks---12-x-18/p/27038Female DC Threaded Barrel Jack Panel Adapter 5.5mm x 2.1mm Connector -...

Link para baixar o código fonte do Andon para Idosos: https://drive.google.com/drive/u/0/folders/1RaliG8NojmpPJShhHJO0mLMaInkms1hZ --------------------------------------------------------- Series - ESP32 - S01E04 - Andon for the Elderly + MQTT Have...

https://www.thingiverse.com/thing:3987784 BOM: Front idler wheel axels - 2x 37mm standoffs...

For now, I don't need to worry about automated watering, but this could be easily implemented by connecting another transistor to an ESP32 and controlling a water pump – we'll see how it goes in warmer months. At the top of the greenhouse, you'll...

different ESP8266 or ESP32 boards, Raspberry Pi Pico, Arduino Nano, …), the surface of this holder just mimics a breadboard by providing a 0.1" grid. The holder as such is stackable, so that you can put multiple DevBoard holders on top of each other....

Prefer restart from STL files.Useful rocket and LED accessories from community...

here: https://de.aliexpress.com/item/4000544411175.html or anywhere else :-) Building the Gadget together is quite easy: solder an ESP8266 or ESP32 to the LED Matrix add the "led matrix holder" between the Microcontroller and the Matrix solder a...

Learn Guide https://learn.adafruit.com/funhouse-fume-extractor/ Project Video by Noe https://youtu.be/B5svMzlKLrY Project video by Liz https://youtu.be/3rwHkWDBnlA Use CircuitPython libraries and ESP32-S2 to connect to WiFi and log sensor data to a...

It uses an inexpensive ESP32 board by EZSBC.com which can handle being powered by 4 AAA batteries and draws less than 15 microamps when put in the sleep mode with the RC servo attached. It uses a MG995 servo with a coupler pressed on the metal...

Introduction Video: https://www.youtube.com/watch?v=R7TqIVRpjz0 Here is the link to the firmware source code (please contact me me for plattform access): https://gitlab.fhnw.ch/smart_classroom/smart_classroom...

This is a upgraded Case for the TTGO T-Team RDZSone tracker board with a 2.0 TFT Display.Print instructionsParts1x LILYGO® TTGO T-Beam V1.1 ESP32 433 Mhz WiFi Bluetooth GPS1x 2.0" ILI9225 SPI TFT/LCD4x M2.5x10mm Flat Head Hex ScrewsAssemblyPrint...

All parts can be printed with normal settings, except the diffusor.DiffusorPrint at 0.2mm layer height (first layer as well!) with, I'd recommend White PETG, as PETG seems to be a bit more translucent than other plastics, but try experimenting...

In my design, an Adafruit ESP32 drives an inexpensive stepper motor and driver, which in turn drives two slotted cams (one controlling the A, B, F and G segments, and a second controlling the C, D and E segments) such that the model counts from 0...

###Arduino UNO (and all compatible shields) DIN rail mount ####Compatibility: [Arduino UNO R3](https://aliexpress.com/item/1005002379248792.html) [ESP8266 WeMos D1 R3](https://aliexpress.com/item/1005001436547177.html) [ESP32 для Wemos D1...

It is build on ESP32-Cam combined with 2 motion detection sensors, 1 temperature sensor and a buzzer for audio notifications. Besides the use of security (Cam & Motion detection) it also services roles in light control and doorbel control. I have...

I am using a ESP32 development board with WLED software to power the lights and am really happy with the result, we use it for a night light for our oldest son. Also modified the top and base a bit as they had 90 degree overhangs which causes...

Battery: - Turnigy 2000mAh 1S 1C Lipo - Dimensions: 49 x 34 x 10mm -...

Again, PETG is a must here.A 3D printing pen is recommended for joining the base pieces togetherFor the electronics, I recommend following NCPlyn's build on GitHub!https://github.com/NCPlyn/ProtogenHelmet-ESP32For the easiest build, get MAX7219 LED...

Prefer restart from STL files.Useful rocket and LED accessories from community...

  Hardware & SoftwareHardware: DSTIKE OLED Wifi Deauther MiNi: https://maltronics.com/collections/deauthers/products/wifi-deauther-oled https://dstike.com/products/dstike-wifi-deauther-mini 400mah 3.7v LiPo Battery:...

... It's already built, but not in action. Got the ESP32-C3 crashed by trying to fix the bootloader. Device is not at mine rn. It's an open project (hence the 0. namenig). ...Would love to see remixes and own attempt of recreating those installations.

Currently Working on a BASE/ standThat houses the esp32 with Potentiometers to adjust the speed, colors, brightness.I am getting back into finishing this from a LONG HOLD (started MAR 2023 butt had too many projects going on to finish this one.) and...

The code is designed for an Arduino or ESP32/ESP8266 platform, judging by the presence of `delay()` function calls. Here's a breakdown of what the code does: **Variables and Constants** The code uses several variables and constants: * `leds`: an...